DIY Rocking Chair Makeover with Spray Paint and New Fabric
That’s right — I used the word dastardly. We should probably be working on our office cabinets, but that’s a big job (a weekend or maybe two), and I’ve been giving this rocker the stink eye since November — long before we moved. For anyone who needs a reminder: I picked it up on Craigslist for $25 because I liked the simple lines. Then it sat untouched for over nine months until this weekend.

The main reason for the delay was intimidation. I knew how to reupholster a seat, but the hole at the top of this rocker had to look finished on both sides and that completely baffled me. After posting a call for upholstery advice a while back and hearing many different approaches, I felt encouraged — and finally decided to give it a try. I mixed reader tips, some online searching, and advice from a friend who reupholsters regularly, then improvised as I went.
This was a multi-day, multi-phase project, so I’ve broken the process into stages. Here’s the first half of the makeover, documented step by step.
I started by stripping the chair: pulling staples, tacks, and nails to expose the frame so I could see what needed repair. My recommendation: use small channel-lock pliers for removing staples and tacks. They grip better than a hammer claw or needle-nose pliers and reduced tool slippage.

After a few hours I had a decent pile of old hardware and fabric, and then removed the two wood seat slats so I could work on them separately.

The frame needed wood putty and sanding to smooth imperfections, but I put that off for a bit and tackled the seat pieces first. I taped the two thin wood slats together with delicate surface tape so I could upholster them as one continuous piece instead of dealing with a seam later. Then I layered extra-loft batting for the right level of comfort.

I used “Soft N Crafty” batting from JoAnn and applied five layers to create a seat that’s plush without being overly soft. I considered foam but opted for a firmer, more traditional wood-seated feel.

After stapling five layers, I realized the seat still needed to bend slightly to pass between the chair arms and legs and sit flat on the base. I nearly panicked at the thought of unstapling and restapling everything, but my husband suggested I flip the seat over and cut the tape on the back so the batting could fold forward just enough. That worked perfectly.

For fabric I used a Kravet Design remnant I found on clearance — a patterned fabric that required centering. I roughly folded the fabric around the seat to find a center line, then flipped the piece over and placed a single staple at the top middle and bottom middle to hold it in place. That allowed me to check alignment and adjust easily before committing to the rest of the staples.

Once centered, I stapled at the four cardinal points — top, bottom, left, right — pulled the fabric tight, then continued stapling around the perimeter. For the carved corners I folded the fabric like wrapping a present, pulling taut and securing folds with a few staples so the front looked smooth and neat.


I reinstalled the seat to confirm it could still hinge forward slightly to fit into place — it did, and I breathed a huge sigh of relief.

Next came the frame prep: filling visible holes with wood putty, sanding to smooth and rough up the surface, and wiping with a liquid deglosser to get it ready for finish. I had hoped to use a rich dark stain, but after patching and sanding it was clear the wood would absorb stain unevenly. Rather than risk a blotchy finish on a $25 Craigslist find, I chose to paint.

I sprayed the frame with oil-rubbed bronze spray paint in three thin, even coats. The paint has a built-in primer and a subtle metallic quality that gave the chair depth and the look of dark wood without the inconsistency stain would have shown. Spray-paint tip: lightly mist each coat and keep your arm moving to avoid drips and achieve even coverage.


Update: A reader pointed out that the fabric I used recently appeared on the cover of a catalog and that the same fabric and finished chair are sold commercially at a much higher price. It’s funny to find something you bought for a few dollars mirroring a product that sells for hundreds.
So that’s Part One of the rocker restoration: stripping, batting and fabric on the seat, and painting the frame. Part Two will cover final assembly and the finishing touches, plus after photos. Have you put off a project for months because a detail intimidated you? What tricks helped you finally get it done? I’d love to hear if you’ve solved a similar upholstery or repainting puzzle.








