How to Build a Vented Built-In Cabinet to Hide Your Microwave
Remember that microwave we scored a great deal on a couple of months ago? We ended up returning it.

When we first bought the 30″ model some readers asked why we needed such a large microwave. That made us rethink how often we actually use the microwave: occasional soup, reheating leftovers, or defrosting. Once we pulled down the original black over-the-range microwave — which had been as wide as the oven at 30 inches — we realized how imposing a new 30″ unit would be next to the pantry.

We had originally imagined building it into the cabinetry, similar to what we did in our first kitchen, but that placement would put it flush against the window and look too bulky.

After living with the lighter, more open feel in the kitchen for a couple of weeks, we decided to return the large unit and buy a smaller countertop microwave — an 18″ model — for $84. It’s a modest, practical size that suits our needs.


We didn’t intend for this smaller microwave to live on the counter forever. Our plan was to build it into an existing cabinet so it could be hidden when not in use and still vent properly when it’s on.

One of our old upper cabinets fit the new microwave almost perfectly in width. The cabinet frame narrows the visible opening, so inside there’s a couple inches of extra clearance on each side. Two issues remained:
- The cabinet was too tall for its intended location next to the pantry and would hang awkwardly at that height.
- It wasn’t deep enough for the microwave to sit back and appear flush, plus the appliance needs ventilation space at the back or side depending on the model.

We planned to shorten the cabinet, add a ventilation opening in the back, and add a door so the microwave can be hidden when not in use. We’d already had an electrician install an outlet where the cabinet would hang, so the unit would be powered and ready. Many custom kitchens integrate microwaves like this, and it can look clean and function well — just be sure to check your microwave’s manual for ventilation requirements.
First, I removed the metal shelf rails, which came out easily, then measured carefully, marked the cut lines, and used a jigsaw to trim the cabinet down to the proper height.

After measuring, leveling, and double-checking, I made the cuts along the marked lines.


To address depth and ventilation, I cut a hole in the back of the cabinet and notched the interior frame so the microwave door can swing open easily. The notch allows us to shift the microwave slightly to the right so the left hinge has room to open without rubbing the cabinet frame. The notched area will be hidden once we install the cabinet door.



From the front, the arrangement already looks tidy, and the visible notch is small and will be concealed by the door.

I added a shelf above the microwave by installing fixed ledges to support it, which gives extra storage space for cookbooks or plates.

Next, the cabinet needed a top and extra support along the back so it could sit a couple inches away from the wall for ventilation. I sketched a quick plan, picked up some wood, and built a new top from a thin sheet of plywood, a pine front piece, and a scrap 2×4 for reinforcement.


Along the back I attached doubled 1×4 blocks so the cabinet would sit away from the wall and provide solid anchor points for hanging. I routed wide channels in some of those blocks to allow warm air to vent up and out the top of the cabinet.


Finally, I fitted a thin side panel, clamped it in place, and nailed it in. After those steps the cabinet began to look more finished and cabinet-like.


With my assistant’s help we hung the modified cabinet in place, showing the vent openings on the back and side. I drilled ventilation holes in the left side to take advantage of the gap between the cabinet and the pantry frame.


We set the microwave into the cabinet and plugged it into the outlet the electrician had installed. Once we add a cabinet door and paint the unit the installation will be much cleaner; in the meantime, a few cookbooks and plates help it look more finished.


Update: That small routed area will only be visible with the door open. Many cabinets look cluttered inside when open, so our approach is simple: if the doors are closed and the kitchen looks good, we’re happy.
We plan to install the cabinet door soon. Here’s a rough mockup showing how the door will conceal the routed area when closed. The area will remain open only during microwave use.

With this cabinet in place there’s now 14″ of space to the right between the cabinet and the window above the sink. Once we hang new 12″ deep floating shelves on the oven wall, they’ll sit 14″ from the window edge as well, which will help the kitchen feel balanced rather than crowded.
Returning the oversized microwave also helped our budget. We got $255 back for the large unit, sold the old over-the-range model for $90, the old kitchen table and chairs for $120, and our old granite counters for $350. After buying the smaller microwave for $84, we put about $731 back into the remodel budget — a welcome boost as we continue through the middle stages of this kitchen makeover.

We still have a lot to do before the kitchen is finished. Our next tasks are practical steps to get everything ready for paint and final finishes:
- Trim down the doors for the cabinets we added.
- Add window trim and build a window sill (we previously stripped back the window).
- Add toe kick around the cabinet bases for a unified look; we’ll save shoe molding for after the cork floors are installed.
- Remove all cabinet doors, check fit and alignment, fill holes and gaps with wood putty, and sand.
- Prime everything.
- Paint — after that comes the fun: final lighting, cork floors, backsplash tile, floating shelves, and a built-in range hood.
One cabinet at a time. What are you working on in your kitchen — demo, holiday cooking, painting, or just microwaving?








