How to Install a Range Hood (DIY Step-by-Step)
“How’s it hanging?” was the big question last week—not a casual greeting, but the practical kind: how were we going to hang the $60 range hood we found on Craigslist?

Sherry wrote last week about our plan to build a simple wood cover for the hood (see the inspiration in last week’s post). We were thrilled about the price and the look, but we hadn’t fully thought through a key step: how to actually install an under-cabinet hood when you don’t have cabinets above the stove. In hindsight, that was a pretty big oversight.

My first instinct was to search for tips on converting an under-cabinet hood to a wall-mounted unit. After a few fruitless searches I began to worry this might not be possible. Then I found these wall-mount brackets from Kenmore and realized others had solved the same problem by using brackets designed to mount hoods without overhead cabinets.
We didn’t buy that specific kit—our hood is Jenn-Air—but the bracket listing confirmed that wall-mounting an under-cabinet hood was doable. So we made a plan: build a makeshift mounting panel from wood, use heavy-duty metal brackets to reproduce the support a cabinet would normally provide, and proceed carefully.

Before we started, there were a few details to fix—like realizing we hadn’t tiled high enough under the vent pipe. That meant a quick trip back to the tiling phase for eight thin rows of tile. It was annoying, but a 20-minute patch with thinset and spare tiles got us back on track.

Next we mapped everything on the wall so the hood, shelves, studs, and stove center would all line up. It looked a little chaotic with painter’s tape everywhere, but the markings were essential:
- 1 & 2: Placement for floating shelves so the bottom of the hood would align with the top shelf—about 34″ from the countertop, which falls in the manufacturer’s recommended 30″–36″ range from stovetop to hood.
- 3, 4 & 5: Stud locations to ensure the hood would be securely anchored.
- 6: The stove center, so the hood would hang squarely over the cooking surface.
If you’re wondering how we found the studs, Sherry had the foresight to mark them while the wall was open. I put small marks on the ceiling above each stud, taped a thread to each mark, tied a paper clip to the bottom as a weight, and let it hang to transfer the position down the wall. Those ceiling marks will be hidden once we install crown molding.

With guides in place, we screwed the first plank of wood into the studs. The hood could technically reach two studs on its own, but the mounting slots in the hood didn’t line up with the studs, and we didn’t trust a direct attachment. Our solution was to secure a wider board into two studs (and use a heavy-duty anchor in a third spot) and later hang the hood from screws that matched its notched mounting holes.

We double-checked the plan with a contractor to avoid drilling into the tile blindly. Then came the scary part: drilling through the tile. I used a special glass-and-tile bit and worked slowly with steady pressure. It took focus, but we got the holes we needed without cracking tiles.

After drilling six holes, we fastened the chunky plank with 2.5″ screws into the studs. Feeling those screws bite into wood was reassuring—we knew the board would bear the hood’s weight. Next we added a second board mounted slightly higher to support the brackets; this one was also screwed into studs and reinforced with heavy-duty anchors.

Note: the vent pipe looks off-center in some photos, but the boards are straight—once we build the wood hood cover the visual alignment will be corrected. The blue arrows in one image point to the two screws the hood will hang from.

We realized we weren’t doing anything unusual: upper cabinets are typically attached to studs with screws, then loaded with dishes and sometimes a hood—so a hood mounted solidly to studs should be stable. Putting the hood up was nerve-wracking, but it clicked into place and felt solid. For safety, Sherry supported it while I attached the brackets to the wood panel and into the hood’s mounting slots—the same spots that would attach to a cabinet.

Once both brackets were secure, I finished the vent connection and plugged the hood in. (Lucky for us the hood’s power cord lined up perfectly with our outlet.) We later learned a tip from readers: metal foil tape is better than duct tape for sealing duct joints, so we switched to foil tape for a long-lasting seal.

At this stage things look a little rough—the exposed vent pipe, the wood mounting boards, and the unfinished ceiling hole aren’t pretty—but it’s a functional start. The hood is positioned about 34″ above the countertop, which falls in the recommended 30″–36″ range from the stovetop, and it has two light settings, which feels like a luxury after months without a hood.

The exposed wood edges stick out roughly an inch on each side, but that’s intentional: they’ll make a secure attachment point for the custom wood hood cover we’ll build next. We still need to snap in the stainless-steel filters, which will improve the look from below, and then build the finished wood cladding.

If you’re worried the hood might fall, we were too—so we pulled the stove out the first night just to be safe. After several days with no shifting, creaks, or signs of movement, we’re confident this mount is secure. The combination of long screws into studs and heavy-duty brackets provides both bottom and top support.

Next up is the fun part: building the wood cover to give the hood a finished, custom look. We’ll share that process soon with step-by-step photos. In the meantime, what projects did you tackle this weekend—did you mount anything heavy, drill tile, or use creative support tricks? Oh, and something big is starting in our house today (it’ll run for the next three weeks), so we’ll report back with photos once we survive the first day.








