DIY Kitchen Shelves: How to Hang and Install Securely
Installing and Painting Open Shelves: A Kitchen Progress Update
In our previous post we had primed the open shelves in preparation for hanging them. With the primer ready, we also primed the hood cover so the whole wall would read as one cohesive surface instead of feeling overly wood-toned.

To paint the hood cover we worked the paint into the cracks with a 2″ angled brush and finished with a small foam roller to create a smooth, even surface. The transformation was immediate — the wall started to feel much lighter and less rustic once the primer and paint went on.

After the primer had dried on both the hood cover and the shelves (we used Zinsser Smart Prime, which is low-VOC and recommended by several cabinet painters we know) we applied the same high-durability cabinet paint we used previously. Two thin, even coats over the primer did the job. Like before, we used a 2″ angled brush in tight areas and a small foam roller over larger surfaces for a professional, smooth finish. The paint we chose is Benjamin Moore Advance in Cloud Cover — a popular choice among pros for both interior cabinet faces and exterior surfaces because it cures hard and stands up well to everyday use.

The most exciting part came when we finally put the shelves up on the wall. We were thrilled to see the design start to come together. Since the screw locations had already been marked and drilled in an earlier step, hanging the brackets and shelves went smoothly.

We mounted the brackets on the shorter section of wall first, then lifted the shelves into place. Seeing the clean lines and bright paint against the tile was a nice reward for the prep work.

Before securing anything permanently, we double-checked that everything was level — which it was — so we could move on with confidence.

Next we installed the shelves along the longer side of the wall so the whole array would be consistent and balanced.

Originally we planned to fasten the shelves directly into the wall and even created pocket holes in preparation. After feeling how sturdy the brackets were, though, we decided to attach the shelves to the brackets instead of drilling additional holes in the tile. We used the pocket hole locations as guides, but drove screws straight down into the bracket rather than at an angle. In retrospect the pocket holes weren’t necessary, but they now serve as hidden attachment points that can easily be caulked over for a seamless look.

Once the shelves and brackets were screwed together we ran a thin bead of paintable white caulk along the top of each bracket. Smoothed with a finger and then painted over, the caulk eliminated dark seams where the bracket met the shelf and made each shelf read like a single, integrated piece. It was a little tedious but absolutely worth the cleaner finished appearance.

With the assembly and caulking complete we stepped back. The hard part was done, but we still needed to let the paint cure fully before loading the shelves with dishes and glassware.

We resisted the urge to immediately fill them. Because we had recently caulked and touched up paint, giving everything adequate curing time was important to avoid scuffs or dents during the first days of use. We’ll load them up after the paint manufacturer’s recommended cure time — and tomorrow we plan to photograph and record a short time-lapse of the shelving being stocked.

We still have a few finishing touches on the checklist: installing crown molding along the ceiling to blend the hood top, patching a couple of ceiling spots, adding a pendant over the sink, covering the base of the peninsula with decorative wood planks, hanging artwork near the fridge, and addressing the side of the pantry. But seeing the painted hood and the new shelves in place makes the space feel much closer to completion.

We’re pleased with the decision to use visible brackets instead of true floating shelves. They have personality, they’re rock-solid, and they give us plenty of usable space — the shelves are deep enough for 12″ dinner plates and the brackets are spaced 15″ apart, which will accommodate everyday dishes and keep them within easy reach.
Despite the initial oddness of breaking the continuous penny tile with bright white horizontal lines, the contrast actually highlights the design and brings the vision we had for this wall to life.


Tomorrow we’ll share photos and a short video of the shelves fully styled. For now we’ll enjoy this near-finished view and the big difference it makes compared with how the room looked when we first started the makeover. It’s rewarding to see months of work begin to read as a cohesive, finished space.


If you’re looking for shelving or vertical storage ideas, consider DIY shelving projects that maximize accessibility and keep frequently used items on display. Open shelves work best when they hold items you use regularly — they stay practical and avoid collecting dust.








