Objectales

Popular

How to Install Floor Trim, Transition Strips and Reducers

featured 46475

Since sharing this photo over a month ago, several readers asked for more detail about how we finished the transitions around the cork floor in our kitchen and around the fireplace surround.

img 46475 1

Keep in mind we plan to refinish the adjoining rooms with the orange wood flooring to match the darker cork tone, so the finished look should resemble this mockup (forgive the rough Photoshop job):

img 46475 2

Finding the right transition pieces took some searching because our Lisbon Cork didn’t have matching trims available. At Lumber Liquidators they advised against cork transitions, noting that cork is softer and can show wear where transitions get kicked and bumped. They offered oak transitions we could have stained (around $45 for a 72″ piece), but I found an engineered option at Home Depot for about $27 that already matched the cork closely. The catch: Home Depot only stocked 48″ pieces locally, so I had to special-order the 72″ lengths and wait a few weeks for them to arrive at the store. That’s why only our shorter doorways were finished back in March when we completed the flooring. It was about time to finish the rest.

img 46475 3

There aren’t many step-by-step guides specifically for transitions on cork floors, so I’ll describe what worked for us. I didn’t photograph the original kitchen install, but we documented the recent doorway and fireplace transitions we completed last week.

img 46475 4

Because we installed our floating cork floor over an existing substrate (we had to leave the old floor in place due to an asbestos liner under the vinyl tile), the finished cork sits a fraction of an inch above the neighboring hardwood. In our case that difference is about 1/4″–1/2″. When two floors meet at different heights, a transition piece called a “reducer” lets one side slope down to the lower surface without creating a trip hazard. The reducer has a gentle slope on one side and a small lip on the other, so it connects the two levels subtly—aim for a gradual profile rather than a dramatic C-shape for the most discreet result.

img 46475 5

After removing the protective plastic from the pieces (you can see the markings in a few photos), I marked a cut line with a ballpoint pen to get the right fit and sliced the transition to length on my miter saw.

img 46475 6

Some guides recommend adhesives, but in our homes we’ve always nailed transitions in place. We haven’t bought a nail gun yet, so I set the finish nail by tapping it partly into the transition with a block of scrap wood underneath to support the underside and prevent splitting. If you’re concerned about splitting, pre-drilling a small pilot hole is a safe alternative.

img 46475 7

To position the reducer, I lined it up across the doorway so the lip sat snugly on the higher surface of the cork while the sloped edge met the lower floor. For the area with the largest height difference I actually rested the small lip on the cork’s top edge to hold it steady as I worked.

img 46475 8

After driving the nails flush (we like using an inexpensive nail punch to avoid dents), the result was clean and stable. The doorway is no longer a toe-stubbing hazard, and the transition reads naturally with the floor color change.

img 46475 9

The hallway transition followed the same approach, so I’ll jump ahead to the fireplace surround. The fireplace needed transitions on all four sides and required mitered corners. I measured each side, set my miter saw to 45 degrees, and cut matching miters so the pieces fit together cleanly.

img 46475 10

Currently the fireplace floor sits lower than the cork, so reducers were the right choice again. This is a temporary solution until we decide on tile for the fireplace hearth; a new tile installation will raise the height to be flush and we’ll remove these interim trims then.

img 46475 11

For now, the transition trim looks good and does the job. It’s surprising how much a few trim pieces can make a space feel finished—no more raw edges and everything reads as a complete floor installation.

img 46475 12

Here’s a view from the hallway showing the new doorway transition and the fireplace beyond. Yes, that’s a giant faux clam shell in the fireplace—we picked it up from our Joss & Main collection and it’s become a conversation piece. Several friends have even asked where to find one for their unused hearths.

img 46475 13

And one last shot of all three newly trimmed areas together. Ta-da—our cork floor is officially finished for now. Don’t mind the placeholder rug; it’s leftover from our first kitchen and we’d like to replace it eventually.

img 46475 14

Have you tackled transitions on cork or mixed-height floors in your home? I was surprised at how few cork-transition projects I could find online, so if you’re planning something similar I hope this walkthrough helps. What tips or tricks have you discovered when finishing doorways and fireplace surrounds?