How to Spray Paint Old Brass Door Knobs
How We Transformed 18 Door Knobs with Oil-Rubbed Bronze (ORB): A Simple DIY
You down with ORB? Yeah you know me.
After nearly two years of planning, we finally replaced and refinished every last brass doorknob in our house. It was one of those little, nagging projects that felt intimidating because it involved every door, but the actual work was straightforward and the results are fantastic. Converting bright brass knobs to an oil-rubbed bronze (ORB) finish made the whole house look crisper and more cohesive.

We removed 19 knobs initially with the plan to refinish them. We had previously tested a similar method on exterior knobs, handles, and a doorknocker to see how the finish held up to weather, so we were confident enough to tackle the interior hardware. That initial trial held up well outdoors for over a year, so we moved forward with the full set of interior knobs.

Materials and Preparation
What we used and why:
- Standard screwdriver to remove knobs; we kept each pair together so reinstallation would be fast and accurate.
- Fine-grit sandpaper (around 400 grit) to scuff the surface so paint would adhere. Use high grit to avoid deep scratches that could show through the finish.
- Liquid deglosser to remove residues and create a clean surface for painting.
- Universal all-surface spray paint in oil-rubbed bronze (a can with a built-in primer is ideal for metal).
- Cardboard or a protected surface for laying out knobs while painting and curing.

Step-by-Step Process
Here’s the exact workflow we followed so you can replicate it:
- Remove each knob with a screwdriver and keep matching pairs together. Label or lay them out in order if you have many different sets.
- Sand every knob lightly with 400-grit sandpaper to roughen the surface. Small surface scratches will be covered by paint; avoid heavy sanding that leaves deep marks.
- Wipe each piece with liquid deglosser and lay the knobs out on cardboard standing upright where possible so painted surfaces stay smooth and untouched.

- Shake the spray paint well and apply several light, even coats from multiple angles. Keep the can moving to prevent drips. We did thin mist coats and allowed about 10 minutes between coats; it took roughly five light coats for full coverage.
- Paint all exposed surfaces by rotating each knob and spraying from every side so the finish looks consistent. I squatted and moved around each piece to ensure even coverage.

- Let the painted knobs cure fully before handling. We let them dry for a full 48 hours. After an initial 12 hours outdoors on a warm day, we brought them inside to the sunroom to continue curing; avoid painting in temperatures that are too cold and follow the can’s temperature guidelines.

Time and Cost
Here’s a realistic time breakdown for the entire project:
- Removing knobs: about 30 minutes total.
- Sanding and deglossing: roughly 2 hours.
- Spray painting: about 1 hour of active spraying spread across several light coats.
- Drying/curing: 48 hours passive time.
- Reinstalling: about 30 minutes for all knobs.
Active work time was roughly 3.5 hours plus two passive days of drying. We used one can of spray paint (leftover from another project), making this a very budget-friendly update compared to buying new oil-rubbed bronze knobs, which can be significantly more expensive.
During reinstallation, painter’s tape was helpful to protect the fresh finish from scratches while tightening screws. Remove the tape when you’re done and the finish will remain intact.

Hinges and Strike Plates
Many of our hinges were already darkened from age or painted, so they didn’t clash with the new ORB knobs. If your hinges are bright brass and stand out, you can replace them inexpensively. I avoided spray-painting hinges because hardware that rubs and grinds tends to wear paint off over time.

Some latch strike plates had naturally darkened and matched nicely, but a few were still bright brass. Because strike plates get banged by the latch frequently, we replaced the overly shiny plates with inexpensive ORB-finish strike plates rather than spray-painting them, since new plates are cheap and will hold up better.


Final Thoughts
Completing this project felt great. It was one of those simple but impactful upgrades that makes rooms feel more intentional and less dated. The work itself wasn’t difficult—remove a few screws, sand, spray a few coats, and reinstall—and the payoff is significant. If you’ve been procrastinating similar small upgrades, this is a perfect project to tackle in an afternoon with a couple of passive days for drying.
Update – Want to know where we got something or what paint colors we used? Click the image below in our original post for details.

*This post contains affiliate links to items we have purchased and love*








