How to Build a Pergola Attached to Your Garage
Parking our car felt a little more special this weekend: we finished the carport pergola—our new “cargola.”

Recently we discussed dressing up the carport and used pergola plans to guide the project. The plans removed a lot of uncertainty, but there was still hands-on work to do. All told, the build took roughly 4.5 days (the half day was for picking up materials), and this post summarizes the process and lessons learned so you can replicate the project or get inspired for your own carport upgrade.

There were four main components to the project: the column, the braces, the joists, and the lath. Each step has its own challenges, and together they form the finished pergola that now crowns our parking spot.

Most attached pergolas don’t require a new free-standing column because they fasten directly to existing walls, but our carport only had posts on the left. So our first task was adding a matching post on the right to create visual balance and provide an attachment point for the pergola.

To anchor the new post to the concrete, we used a metal post base designed for that purpose and a hammer drill to make the pilot hole for a concrete wedge anchor. The hammer drill’s hammering action made short work of the concrete. Once the anchor was set, we tightened the nut and secured the post base.

We also attached a metal post base to the ceiling with heavy-duty screws, slid a 4×4 post into place, and nailed it in. Because the structural post alone looked thin and unfinished, we dressed it up with cladding to match the rest of the porch details.

To beef up the post, we primed and painted two 1×6 boards and one 1×4 board, then used a nail gun to fasten them around the post. After caulking seams and touching up paint, the column looked substantial and finished—one major step checked off.

The second major task was fabricating the braces, also called knee braces. These were the most involved pieces. We initially considered buying premade braces but couldn’t find the correct size, so we built our own from 12-foot lengths of 2×6. That saved money—where some braces online sold for $50–$100 each, ours cost roughly $22 apiece in materials.

Each brace required four sub-components: a base that sits against the column, two beams that project outward, and a decorative arch between them. We cut the base pieces, added decorative notches, and bored holes to countersink the bolts that would hold everything together.

The beams were easier and we cut matching pairs together to ensure identical parts. The arch required a curved cut: we bent a thin strip of scrap wood over temporary nails to trace a smooth curve, then cut with a jigsaw and sanded the edges to refine the shape.

After cutting and sanding, we primed all brace pieces. Assembly was a careful process of clamping, temporary fastening, and aligning the beams and arch so we could secure them to the base with 3″ lag bolts. It took patience to keep everything plumb and square, but the result was solid and attractive.

Installing the assembled braces required one person to hold each brace while the other checked level and set temporary nails. We then secured them permanently with lag bolts through the top and bottom. With two braces installed and painted, the structure began to feel real.

Step three was mounting the joists—the long 2×6 boards that run across the braces. These also received decorative curved cuts on the exposed ends. We marked where the joists would rest on the braces, notched the joists to sit tightly, primed and painted them, and then bolted them down from above so they tie into the brace beams securely.

The final stage was the lath: many narrow strips that create the top lattice and finish the pergola’s silhouette. Because we planned to paint immediately, we used standard 2×2 boards rather than pressure-treated pieces, then ripped them to size, sanded, primed, and painted them. Cutting and prepping about 50 pieces took time, but the repetitive work is straightforward and satisfying.

Installation of the lath was the moment the pergola finally looked complete. We used simple 3-inch scrap spacers to keep gaps consistent and screwed the lath down quickly and evenly. Once the last piece was set, the finished pergola transformed the carport from a functional afterthought into a charming architectural feature.

By the end of day four the entire project was complete. We stepped back and enjoyed the new curb appeal and sheltered parking space—suddenly the carport feels intentional and welcoming.

We were surprised at how much personality the pergola added; it frames the view down the street and gives our ranch-style house more architectural depth. The finished look already has us imagining flowering vines climbing the posts and softening the beams.

Cost-wise, DIY made this a bargain compared with custom attached pergolas. Our expenses included a truck rental, lumber, post bases, fasteners, and a few materials to reroute a gutter and an outdoor light. We already had paint and primer on hand, which kept costs down. Here’s the breakdown:
- Truck rental (to transport materials): $19
- Lumber: $112
- Post bases: $23
- Nuts, bolts, and screws: $46
- Materials to reroute gutter and light: $14
- Paint and primer: already owned
- Total: $214
If your carport already has two columns or you can buy pre-made braces, the project becomes significantly easier and faster—potentially cutting a couple of days from the schedule. That’s a great option for anyone wanting most of the visual payoff with less fabrication work.

Between this project and some upgraded porch columns we previously added, we’re falling in love with the front of our house again. The pergola turned a simple parking spot into a charming architectural feature, and it’s already improved the impression our home makes on the street.

Have any outdoor projects on your agenda? Whether you’re considering a pergola, improving curb appeal, or tackling a smaller update, a little planning and a DIY approach can deliver big results without a big budget.









