Objectales

Popular

How to Stain and Seal Your Deck: Step-by-Step Guide

featured 57970

Deck Staining and Sealing: From Power Wash to Finished Deck

After finishing a thorough power wash, we were finally ready to stain and seal our deck — a process we completed and refurnished on Tuesday, just hours before our first showing.

Deck before staining

To recap: when the deck was completed in late August, we were advised to wait 2–3 months so the pressure-treated lumber could dry out before sealing. Sealing too early can trap treatment moisture and cause problems, so we followed that guidance. By the time we could have sealed it in fall, the weather was too cold. After spring arrived, we power washed the deck, but it still wasn’t quite ready — some stubborn grime remained, especially in one corner.

Corner with grime

My partner Sherry thought the stains were barely noticeable, but I wanted the surface as clean and even as possible before sealing. The worry was that any remaining dark spots would be sealed and possibly become more pronounced after staining. So we tried a few cleaners to lift the grime.

Trying different cleaners

The first product we tried was an inexpensive $7 deck wash that attaches to a garden hose. It promised an easy spray-on, sit-for-a-few-minutes, and rinse routine. After following the instructions, though, there was essentially no change — the deck looked the same as before.

Deck wash bottle

After that disappointing result, we were ready to give up, but decided on one more attempt: an $8 Olympic cleaner that required a separate $11 sprayer. I had skipped this originally to avoid the extra tool, but in hindsight the combination made a dramatic difference.

Olympic cleaner with sprayer

The Olympic cleaner essentially bleached the deck surface back to a blank slate. I was briefly alarmed by how light the wood looked immediately after rinsing, but this is a common result with cleaner formulas containing bleach. Once dry, the surface looked even and ready for a uniform coat of stain. So for anyone wondering whether the cheaper hose-attachment cleaner is sufficient — in our case it wasn’t. The $8 cleaner plus the $11 sprayer did most of the heavy lifting.

Cleaned deck ready for staining

With cleaning complete, we moved on to staining and sealing. We squeezed the work into a small window while our daughter Clara napped, hoping to finish before she woke up. Here are the supplies we used:

  1. Olympic Maximum Toner in Cedar Naturaltone (stain and sealer in one, $37 from Lowe’s)
  2. Deck Stain Applicator (sponge-style, $7 from Lowe’s)
  3. Large brush ($6 from Lowe’s)
  4. Rubber gloves (on hand)
  5. Paper towels (or rags)

Stain and tools

We chose a toner rather than a semi-transparent stain to keep the color subtle and let the wood grain show through. The straight-from-the-can color looked orange at first, but it dried to a more muted, natural tone that blends well with the other exterior trim and fencing.

Stain color from can

For application we used the sponge-y deck stain applicator to cover large areas quickly, and then immediately “backbrushed” with the large brush. Backbrushing evens out the stain, prevents pooling, and helps the finish penetrate the grain. I applied with the sponge applicator while Sherry followed closely with the brush, brushing the boards and edges until the finish looked uniform.

Applying stain with applicator

The largest flat section took about 15–20 minutes and only required a single coat, as directed by the product. The stairs and railings were much more time-consuming because each post and railing face needed careful brushing to avoid drips and puddles — that portion took perhaps two hours. Our daughter woke up before we finished, so I went in to entertain her while Sherry completed the railing detail.

Stained stairs and railings

When the stain was still wet it looked a bit warmer and redder than we expected, but once dry it “toned” the wood subtly and matched well with the surrounding exterior elements. Sherry also painted the utility box to blend better with the brick using a small test pot of paint — a quick touch that cost around $2.50 and made the box much less noticeable.

Utility box painted to blend with brick

That stubborn corner that had been especially dirty finally looked much better after cleaning and staining. It’s not perfect, but the improvement was obvious compared with how it looked after just pressure washing.

Improved corner after staining

Finished deck close-up

Eight months after construction wrapped (ten months from start to finish) the deck is officially stained, sealed, and complete. We’ve already enjoyed it through late fall and early spring, but now it’s protected so leaves, acorns, and weather won’t cause as much wear.

Finished deck overview

We also tallied the final budget so you can see how it all added up:

Permit – $114
First lumber & hardware order – $1,007
First auger rental – $60
Second lumber & hardware order – $251
Second auger rental – $60
Flashing – $40
Misc hardware & supplies – $95
Powerwash – $80
Cleaner & Stain – $76
Total: $1,783

You can save money if your project has a smaller staircase or if you don’t need to rent tools a second time after a failed inspection. Buying an effective cleaner the first time can also save you time and money.

This project was one of our biggest DIY builds — up there with a full bathroom gut job — and doing it ourselves saved several thousand dollars compared with hiring it out. More importantly, it gave us confidence: we built a deck that’s solid and finished, and we’re proud of it.

Deck completed, proud owners

This narrow alley and the deck have come a long way since our first walkthrough in 2010.

Deck area during first walkthrough

Are you planning to stain a deck? If your stain looked very bright when wet, don’t worry — it often dries to a much subtler tone. And if you haven’t tried a sponge-style deck stain applicator with a brush for backbrushing, it’s a fast, effective method for covering large areas while ensuring a consistent finish.