Objectales

Popular

How to Prep a Vaulted Ceiling for Wood Plank Installation

featured 60801

How We Lofted Our Sunroom Ceiling: Step-by-Step and Costs

If you like a little demolition, some geometry, and a satisfying before-and-after, this project might be for you. We’ve shown a few sneak peeks of the sunroom ceiling progress, but here’s the full explanation of how we got from closed-in to open and airy.

img 60801 1

Getting the Structure Checked

We left the engineering decisions to a professional builder we know from the show home project. He inspected the cross beams and confirmed the good news: the beams were cosmetic framing for the ceiling, not load-bearing roof supports. That meant removing them wouldn’t require major structural rework — but the rafters above were a few decades old and could use reinforcement to be stronger long-term.

Reinforcing the rafters involved adding hangers, ties, and bolts — a lot of nailing, drilling, and ratcheting — which is totally doable but time-consuming. The builder suggested we get a contractor’s estimate just to see what it would cost to hire pros to do the reinforcement and removal.

img 60801 2

Hiring Pros for the Heavy Lifting

We called a contractor recommended by the builder. David and a helper came the next day and removed the cross beams and reinforced the rafters in about two hours for $200. That was an easy decision — faster and more efficient with the right tools and experience. Within a few days of sharing our initial update, the work was happening right outside our living room window.

img 60801 3

The visual change was dramatic. Gaining roughly four feet of height on one side made the room feel much more open. The only remaining eyesore was the fan wiring that now dangled where the old ceiling used to be.

img 60801 4

Electrical Work: Extending Wires and Adding a Second Fan

We called our favorite electrician to extend the wiring so fixtures could attach to the new, higher ceiling. They also converted our single fan box into two so the room can stay cooler and better circulate air. We expect that part of the job to come in around $250.

Going into the project we had budgeted roughly $1,000 if structural changes and permits were needed, not counting any outsourced electrical work. Since the ceiling framing turned out to be cosmetic, we avoided major restructuring and the added expense of permits. Having the contractor and electrician complete the crucial, professional parts for roughly $450 while we handled the initial drywall removal ourselves and plan to do the insulation, fan installation, and beadboard ceiling installation will save us a significant amount overall.

img 60801 5

Starting the Ceiling Rebuild: Triangular End Caps

With the rafters reinforced and wiring handled, we turned our attention to rebuilding the exposed ceiling. The first step was covering the two triangular end sections of the lofted ceiling. Since the rest of the space was framed in plywood, we decided to use plywood panels for the triangles and paint them to match.

img 60801 6

Measuring and Cutting Plywood for a Perfect Fit

I briefly spiraled into 9th grade geometry, measuring angles and hypotenuses, until I realized the cuts didn’t need to be complicated. I only needed a few straightforward measurements. My plywood sheet was 8 feet (96 inches) long, so I knew I’d cut two pieces to fill the space. The height at the brick wall end measured 40.5 inches, and the height 8 feet away measured 17 inches. From those full-height measurements I trimmed 3 inches at each end to account for the beadboard ceiling edge that would later cover the seam, then snapped a chalk line between the two marks and cut along it with a circular saw.

img 60801 7

To make the second piece, I used the scrap edge that already had the correct angle and marked the dimension that needed to match the first piece. With a perpendicular guide line to the angled edge, I made the cut and had two pieces ready for installation.

img 60801 8

img 60801 9

Preparing the Wall and Installing the Panels

Before hanging the plywood, I fanned out the studs so the new panels would sit flush with the existing wall surface. I cut a spare 2×6 into short blocks and screwed them into place as backing. I then test-fit the first large piece, brad-nailed it temporarily, and followed up with heavier nails driven by hand. The fit was gratifyingly snug.

img 60801 10

img 60801 11

One side went up cleanly, although there’s a small seam where the new plywood meets the old wall along the bottom. We’ll caulk that joint and cover it with trim, and use wood filler or Bondo to minimize the vertical seam between the two plywood pieces before priming and painting.

img 60801 15

After finishing the first end, I repeated the process on the other side. That panel required cutting an opening for an electrical box the electricians had installed to organize the wires — the box is intentionally visible and accessible for code compliance. Once primed and painted white, the plywood should blend in with the rest of the ceiling.

img 60801 17

The Big Reveal and Next Steps

Removing the doors and popping the ceiling completely transformed the space — it hardly feels like the same room anymore. The lofting opened the room, improving sightlines and volume so much that the improvement is immediately noticeable.

img 60801 18

With the structural and rough electrical work complete and the triangular plywood infill installed, we’re ready to move on to the beadboard ceiling. That will involve measuring, priming, painting a light blue finish we’re excited about, and then hanging the beadboard. We’ll share that update as soon as the materials are ready and the first boards go up. What did you work on this weekend?