How to Install Porcelain Tile in a Laundry Room
A new tiled floor in a freshly finished room is almost enough to make me do jazz hands (Sherry’s enthusiasm threshold is clearly much lower than mine). We’re thrilled with how this laundry room turned out, and since a saw played a surprisingly romantic role, here’s a clear walkthrough of our laundry room tile installation—from subfloor prep to grouting and sealing.

Before laying tile, the subfloor needed to be prepared with cement board, which is the preferred substrate for tile installations. The sheets come in 3 ft × 5 ft pieces; in this room I fit two full sheets and a few strips. I scored them with a utility knife and snapped them along the score line to cut them to size.

After dry-fitting the cement board, I adhered each piece with thinset. That thinset layer between the cement board and the wood subfloor keeps the boards from grinding, flexing, or shifting over time. I mixed the same thinset I planned to use for tile, following the bag instructions and using a mixing paddle on my drill. I’ll touch on mixing technique below.

I applied the thinset with a 1/4″ notched trowel: spread the base coat with the flat side, then combed grooves with the notched side—the same technique used for tile. Then I pressed each cement board piece firmly into place, leaving about a 1/8″ gap to the wall around the perimeter.

To secure the boards while the thinset cured and to stabilize them long term, I screwed the edges every 6–10″ with cement board screws, and I added screws in the field every 12–16″ as well.

Instead of fully taping and hardening all seams right away, I applied mesh tape to the seams and planned to embed thinset over them during the tile setting. That approach helped me avoid creating high ridges at seams or screw holes that a thick initial coat might have caused.

With the subfloor set, we dry-fit the tiles to figure out the best brick-pattern layout. Initially we centered the pattern, but that would have left thin slivers at the edges. After experimenting, we shifted the pattern slightly toward the left wall so a full tile landed there and larger cuts would be on the right—where a base cabinet and doorway will mostly conceal them. That also complements the offset placement of the washer and dryer.

Cutting tiles became far easier once we upgraded to a full-size wet saw. After years of using a small hand-me-down saw, the larger wet saw—complete with a stand, water tray, and laser—made straight, repeatable cuts much faster and less tiring. The rolling tray makes feeding tile through the blade fast and accurate, which saved a lot of time.

Before setting tile we sorted through all the boxes to pick our favorites. We wanted tiles with strong veining and movement in visible spots, so we created three piles: favorites for the center of the room, regular tiles for edges, and a third pile for the appliance area where the flooring would be mostly covered.

Key supplies for laying the tile (excluding the wet saw):
- Bucket and drill mixer for thinset
- Margin trowel for scooping thinset
- 1/4″ notched trowel for spreading thinset
- Pencil and square for marking cuts
- 1/16″ spacers to keep joints consistent

I intentionally mixed the thinset a bit wetter than I usually do—aiming for a consistency closer to pancake batter—to improve adhesion and workability. I worked two rows at a time and made cuts as I went, checking a long level frequently to ensure a flat, even surface.

The actual tile setting went quickly—once I started placing tiles, it took under two hours to set them all. I left the installation to cure for about 48 hours before removing spacers in preparation for grouting.

We tried to make the doorway transition as seamless as possible. By extending the hardwood slightly into the doorway and planning the subfloor height in advance, the tiled floor ended up perfectly flush with the wood—no raised transition strip required.

Grouting came next after letting the thinset fully cure. Our material list for grouting included a small bucket, non-sanded grout (for joints under 1/8″), water, a rubber float, and a sponge. I mixed grout by adding powder to water until I reached a workable consistency.
- Non-sanded grout in a gray tone
- Float for spreading grout into joints
- Clean sponge and microfiber cloth for cleanup

Using the float, I pressed grout into the joints and scraped off excess at a shallow angle. With large tiles, grouting moves quickly; I completed the room in about 20 minutes. After initial wiping with a slightly damp sponge I let the grout haze set up, then buffed the surface with a dry microfiber cloth to remove remaining film.

We followed up with a grout haze remover where needed, then allowed everything to dry about 12 hours before applying a penetrating sealer to both tile and grout. Sealing protects the grout from staining and enhances the look of the tile.

Those final steps—haze removal and sealing—made a noticeable difference. What had looked slightly dull came to life once the protective sealer was applied.

Cost breakdown for the floor project:
- Cement board & screws: $48
- Tiles (Blast Anthracite 12 × 24″): $353
- Thinset: $29
- Grout (Dolorean Gray): $13
- Buckets, sponges, trowels, spacers, float: $8 (we owned most; add ~$25 if you need to buy them)
- Haze remover and penetrating sealer: items on hand (retail ~$9–$13)
- Total: $451
So roughly $350 went to tile and about $100 to supplies. I excluded the wet saw in that total because it’s a general tool we’ll use for many projects, though upgrading from a small saw made a dramatic difference in speed and cut quality.
With the floor finished, we can begin installing cabinets. We plan to hang upper cabinets before moving the washer and dryer in—dropping cabinets on appliances is not a risk we want to take. Once cabinets are in, we’ll finally be able to wash at home again. High five!









