Objectales

Popular

Build a Console Table: Step-by-Step DIY Plans

featured 34718

DIY Console Table: Building the Hidden Storage Center Piece

After finishing the two end sections of our three-piece DIY console table, I turned my attention to the middle section. This center piece sits hidden between the other two sections, sandwiched between the back of the sectional and the wall. Because it won’t be highly visible, we could have made a simple platform to support the long tabletop that will span all three units, but we decided to use the space for hidden storage instead. The goal was a sturdy wooden frame with a solid bottom and fabric sides to create a lightweight, inexpensive storage bin inside the middle console.

img 34718 1

The finished center console is 41″ long with an opening in the top and a raised platform shelf that forms the bottom of the storage compartment. To save time and weight we planned to staple taut fabric around the inside perimeter instead of building full plywood sides; this keeps cost and weight down while still providing a usable enclosed bin for baskets, toys, remotes, or blankets.

Materials for the project were straightforward: a stack of 1 x 4 boards and a 1 x 12 board. We had several boards roughly cut at the home center and finished the precise cuts at home with a miter saw. Because much of the piece is concealed, exact face-grain matching wasn’t necessary, but square, strong joinery was important for stability.

img 34718 2

First I cut four legs at 24″ tall. A quick reminder: ripping one long board into two equal pieces isn’t always perfectly exact because the saw blade removes material. I compensated for that by aligning parts to the truest 24″ piece as I assembled the frame so the finished height stayed consistent.

img 34718 3

I attached a long top rail to connect two legs and ensure each end was level. For joinery I used a pocket-hole jig system (Kreg Jig) to secure rails and supports quickly and strongly. The same method was used on both ends and on the other sections of the console table to keep everything consistent.

img 34718 4

img 34718 5

Shorter boards were used to connect the two end assemblies and to form the supports for the lower shelf. To build the shelf economically, I laid two 1 x 4s flat across the support runners and then centered a 1 x 12 on top of them. The 1 x 12 filled the remaining depth and provided a solid, continuous shelf surface suitable for storage.

img 34718 6

img 34718 7

The top of the center piece is two lengths of 1 x 12 left over from the end pieces, attached to either side to leave the intended hole in the middle for access. Once fabric is stapled to the interior perimeter, the storage bin will be discreet, and we may add smaller baskets for organization. The long reclaimed pallet countertop we plan to lay across all three consoles will cover seams and make the entire unit look cohesive while still allowing a removable top section for access.

img 34718 8

img 34718 9

After assembling the center console we moved all three pieces into the room to test fit, even before staining or creating the final reclaimed pallet countertop. The new arrangement tightened the relationship between our sectional and the media cabinet, made viewing the TV and reading subtitles easier, and opened up possibilities for balanced lighting with two chunky table lamps on either side of the finished console.

img 34718 11

One small challenge: the floor in this room is slightly uneven. The console spans almost 140″ once the three pieces are combined, and a small peak in the floor made two of the pieces sit out of alignment. We solved that with adjustable leveling feet—similar to appliance feet—that screw into the bottom and can be spun to fine-tune height. To install them, I drilled a progressively larger hole for the plastic guide, then screwed in the adjustable foot. Where only a small lift was needed, felt pads were enough.

img 34718 13

img 34718 14

img 34718 15

img 34718 16

img 34718 17

img 34718 18

With adjustable feet in most corners and felt pads where only minor adjustments were needed, the finished center console sat level with its neighbors. That small effort transformed the ensemble from a slightly awkward cluster into a cohesive, functional unit. One happy surprise: the center piece still allows access to the wall outlet behind it, which will be essential for powering table lamps once the console is fully finished.

img 34718 19

img 34718 20

Next steps include stapling fabric to the inner sides to finish the hidden storage bin, staining the pieces, and creating the reclaimed pallet countertop with a removable access panel over the middle storage area. We’ll document those steps with photos and notes, but for now it’s rewarding to enjoy a well-leveled, functional center console that makes good use of otherwise wasted space.