Objectales

Popular

Build a Fireplace Mantel: DIY Step-by-Step Guide

featured 56691

Ready for the next stage of the fireplace transformation? Good—there’s been a lot of progress. Previously we’d tiled the hearth and part of the surround with marble subway tile.

img 56691 1

That tile work was the more straightforward part. The next phase—building out the rest of the frame—required quite a few additional materials and a bit more planning.

img 56691 2

We chose MDF for the frame because it’s lighter, smoother, and more affordable than solid wood. The panel we used was a 4 ft × 8 ft sheet that cost just under $35, and fortunately one sheet provided all the pieces we needed.

The first two pieces we built were the vertical sides that sit on the floor and extend up to the mantel.

img 56691 3

I cut the MDF to size and joined the two pieces at right angles using a Kreg Jig and wood glue for extra strength.

img 56691 4

The nail gun quickly became a favorite because it’s so much faster than drilling and screwing everything. Still, since nails aren’t as secure long-term as screws, I used wood glue as backup wherever possible.

img 56691 5

To join the two side pieces, I cut a middle span on the table saw and fastened the three parts together using a couple of scrap 1 × 2″ boards for reinforcement.

img 56691 6

If that previous photo was a little unclear, here’s the frame placed around the original brick fireplace so you can see how it all fits.

img 56691 7

From above you can see the MDF frame sits snugly around the old brick, which, as it turned out, looked pretty rough once the old mantel was removed.

img 56691 8

Because the brick flared under the mantel and tapered toward the floor, there was a small gap between the MDF and the tile in a few places. We filled those gaps with thin strips of MDF so the surround would sit balanced and flush when viewed from the side.

img 56691 9

Here’s the frame from the front so the layout is easier to visualize.

img 56691 10

It was already fairly stable, but we didn’t rely on balance alone. We drove several masonry screws through the top and sides and ran a bead of construction adhesive where the MDF met the brick to make sure the frame wouldn’t move.

img 56691 11

The next step was installing the mantel. The original plan had been to attach the mantel directly to the brick, but the brick wasn’t level and sloped away from the wall, so that approach wouldn’t have worked. Instead we cut more MDF and added a flat top to the frame, securing it with glue and nails.

img 56691 12

We built a new mantel top from a 1 × 10 board and framed the visible edges with 1 × 2 pine strips so no raw edges would show. We also used a few strips of leftover lattice from a previous project to raise the mantel slightly so it matched the old height and covered the unpainted paneling behind it. Keeping the mantel at the same height preserved the proportions we liked while fixing the hearth and side profile issues.

img 56691 13

After the mantel was secured, we added crown molding underneath to give it more presence. Because the crown needed to sit flush with the decorative boxes we planned to add, we first attached a 1 × 3 board to bump the crown out to the correct depth.

img 56691 14

The 1 × 3 allowed an inch of backing for the crown while providing the correct top surface for some of the 1 × 2 box trim to sit against. My wife handled much of the nailing—she’s surprisingly good with the gun.

img 56691 15

With the mantel in place it already felt more finished, but the flat-front look was a little too modern for the rest of our kitchen. To match the more traditional cabinet style across the room, we added baseboard and framed the surround with 1 × 2 trim to create simple decorative boxes.

img 56691 16

We set the baseboard off from the MDF with scrap 1 × 2 backing so it wouldn’t sit flush against the surface and would align with the box trim.

img 56691 17

Then we added vertical 1 × 2 strips, followed by horizontal pieces between them to form the rectangular boxes that give the surround its character.

img 56691 18

To avoid long, skinny rectangles on either side, we added another trim piece where the vertical posts meet the middle span; it helped break up the surfaces and balance the overall design.

img 56691 19

The trim work moved quickly, so we even had time to caulk some seams before our little one woke up and started asking questions about what we were building.

img 56691 20

There’s still work to do: priming and painting, finishing the bottom trim where tile meets the cork floor, and adding quarter round where the baseboard meets the floor. Once those loose ends are tied up the surround will look much more polished.

img 56691 21

Even unpainted, we’re thrilled with how the fireplace makeover is shaping up. For comparison, here’s where we started before the new surround and mantel went in:

img 56691 23

Give us another day or two to finish the paint and final trim, and we’ll return with the completed fireplace, a full budget breakdown, and a bunch of final photos showing the transformation from start to finish.