Build a Planked Wood Desk: Step-by-Step DIY Guide
Our built-in wall-to-wall desk made good progress this week after we painted and raised the cabinets, but it still needed a proper desktop.

Before we added the top, the space looked incomplete.

We needed about thirteen feet of counter, which is longer than many countertop suppliers are willing to deliver without a seam. At first we considered buying a kitchen countertop—maybe butcher block, silestone, or an Ikea option—but many of those would still have a seam. Having saved so much on the cabinets, we toyed with the idea of splurging on the top, but ultimately the decision didn’t come easily.
I was leaning toward a white top to keep things light and to coordinate with the nearby built-ins, while John worried about too much white and possible mismatched tones. We went back and forth until a DIY wood desk we saw inspired us: wood would be the best choice for the look we wanted.
We’ve always loved the contrast of white with deep, rich wood, so using a wooden top felt like a natural way to tie the office into the dining room’s wood table. To keep the scale right for the chunky cabinets below and the long span, we chose 2 x 10″ untreated framing lumber instead of a thinner tabletop. It felt substantial—almost like a giant cutting board—so I may have been a little sentimental with my admiration of the boards in the store.
Home Depot cut a few eight-foot boards in half so we could fit them in the car and maneuver them at home. The total cost for the lumber was only $27.30—under a dollar per square foot—which made it much cheaper than most pre-made countertops.

At home we laid out the boards in the basement to pick the best edges for the front lip and to decide which faces should be hidden along the back. Because we didn’t have a full 13 feet of open floor, some boards overlapped in the mock-up.

I labeled the backs of the boards so I wouldn’t stain the wrong side—an X for “don’t stain this side” and clear notes where the front edges would be.

John handled the sanding since my hands still remembered the vibration from sanding the cabinets. He started with coarse 60-grit paper to smooth out major imperfections and followed with 150-grit for a finer finish.

One common issue with framing lumber is the stamps and ink marks. We picked the faces without printing, but if necessary those marks can usually be sanded away.

After sanding, we moved the boards into the sealed sunroom for staining. We used leftover stain—dark walnut only this time—to aim for a deep finish similar to our dining table rather than a weathered look.

I brushed the stain on and wiped it off after it sat for about a minute, then let the boards dry overnight. The next morning they looked rich and warm.




John originally planned to join the boards side-by-side using his Kreg jig, making larger sections to place on the cabinets. However, once he started, he found those thicker boards weren’t cooperating with that method—especially where a seam would fall over two cabinets. The setup felt unstable, and we didn’t want a wobbly desktop.

Instead he screwed the boards directly into the cabinets first and then joined them to each other where extra reinforcement was needed. That approach required a fair amount of contorting into the base cabinets and coordinating—me holding things steady from above while he drilled up from below.

Wherever possible John used pocket holes to secure the boards together for added strength—he really loves that jig.

One handy trick we discovered was using our camera tripod as a makeshift jack to hold the boards level while John screwed them down. It was a lot steadier and more precise than trying to hold everything by hand.

The whole install, not counting sanding and staining, took most of an evening—probably around four hours—and it was tiring. The trickiest part was dealing with slightly warped boards; we had to finesse and clamp things so the top stayed level as we worked. Once fastened in a few places, things settled into place.
We learned that it’s smart to stain a little over each edge—about a centimeter—because tiny cracks between boards can reveal pale, unstained wood. A small brush and some touch-up stain fixed the few visible slivers.

After touch-ups dried, I applied three thin coats of our favorite low-VOC finish, Safecoat Acrylacq, which adds protection and a rich, slightly glossy sheen reminiscent of our dining table.

The Safecoat not only protects the surface but deepens the color and adds long-term durability.

After 24 hours of drying, we set the desktop in place. Here it is empty:

And with a little quick styling—just to see how it would look in use. Nothing here is permanent; we still plan to hang larger art, finish the walls, and refine the accessories.

I borrowed the lamps from the console and added new shades I found at Target for now. Eventually we’ll pick up two matching lamp bases for the desk area, and the styling will evolve as we live with the space.
From the dining room, the office now reads much more cohesive: the wood top ties in with the table and complements the white built-ins so they don’t clash.

The chunky wood counter provides a warm counterpart to the white cabinets. That vintage green library box I picked up for $4 works perfectly as a drawer organizer for pens and small supplies, while the file cabinets store larger items like the shredder.

Writing on the wood surface hasn’t been a problem. The seams are spaced about four feet apart and the boards are thick, and we usually use notebooks, so the slight ridges aren’t an issue. By chance, the layout left an area to the right of each laptop without any seams, which is ideal for jotting notes.
Overall, this new desktop is a big improvement over our old setup.

Compared to the cramped desk we had before, the new configuration gives us lots more usable surface and a cleaner look.

We’re not completely finished: we still want to add molding around the cabinet bases to make them feel more built-in, and we’re debating whether to change the cabinet hardware finish. Even so, the total cost so far is very low for such a big visual upgrade:
- Cabinets (from Habitat For Humanity ReStore): $6.30
- Kilz Clean Start No-VOC Primer: $0 (leftover; would be around $20 if purchased)
- Electric sander & sandpaper: $0 (already owned; approx. $25 to buy)
- Benjamin Moore Advance paint (Decorators White, satin): $40
- Pre-primed & unprimed wood to build up cabinets (Home Depot): $51
- Framing lumber for counter (Home Depot): $27.30
- Stain & poly for top: $0 (already owned; would be about $8 and $20 if purchased)
- TOTAL: $124.60
For comparison, a 13′ white laminate counter from Ikea would be roughly the same price, and our solution feels more substantial and custom. With the desk done, the rest of the room’s unfinished elements—paint, window treatments, updated chairs, art, and lighting—are more obvious, but we’re taking it one step at a time.
Have you installed a wood-topped desk, dresser, or countertop? Do you sometimes tackle a major build before finishing walls or paint? And does anyone else find lumber strangely irresistible at the home improvement store? We’re curious to hear your experiences.
Psst—if you want to follow the desk makeover from the start, check the earlier posts about office floor planning, the $6 cabinets, cabinet hunting, sanding and priming, and painting and building up the cabinets before adding the countertop.








