DIY Concrete Coffee Table Top: How to Make One
Great news: I finally have a proper place to rest my feet in the beach house living room. In other words, we finally have a coffee table.

light fixture / ceiling medallion / similar rug / similar sofa / similar curtains / curtain rods
This was a DIY project that ended up costing a fraction of the price of high-end alternatives, which is always a win. Since these photos were taken we swapped the rug for a different one, so expect a short follow-up about that and a small dining room tweak soon. For now, here’s the story of the coffee table.

We’d actually had the table base for a long time, but it didn’t have a top for months. A neighbor had listed the wooden octagonal base for seven dollars, so we claimed it and brought it home. After living topless in the garage and then riding in the move to the beach house last fall, it continued to wait patiently until we finally tackled it last month.

Our original plan was to have a stone top cut to fit. Marble or quartz would have looked beautiful, but stone fabricators quoted $700–$900 even for remnant pieces because the round-ish octagon is 38″ at its widest—deeper than a typical countertop piece. Those quotes pushed us to explore less expensive alternatives that would still feel substantial.
After considering faux-stone laminate and painted wood, we settled on a wood core with a concrete-like finish using Ardex Feather Finish. That product gives a chunky, natural stone look without the extreme weight and cost of a poured slab. We’d used Ardex before on kitchen counters, so we knew the finish would look great if applied carefully.

Making the Wood Coffee Table Top
We started with a 4′ x 4′ sheet of 3/4″ plywood for strength and stability. To get the octagon shape, we flipped the base onto the plywood, traced the outline, and cut with a circular saw. That first cut produced an octagon the exact size of the base—no overhang yet.

To create a desirable overhang and a thicker-looking edge without adding much weight, we cut eight strips of 1×2″ whitewood and mitered the ends to 22.5 degrees so they would fit around the octagon. After applying wood glue, we nailed the strips to the plywood edge, producing a snug, almost shoebox-like top that sits nicely on the base. For security, we also attached the top to the base with screws from underneath.

Once the border was nailed on, I filled gaps and nail holes with wood putty. The table base wasn’t a perfect octagon, so a few corners needed extra filling and sanding to look tight and even before the concrete skim coat went on.

Applying the Concrete Finish
We chose white Ardex Feather Finish for a crisp, stone-like surface. Ardex is a thin cementitious skim coat that is mixed with water to a spreadable consistency. A 10-pound bag was enough to complete the table top at a modest cost compared to a real stone slab.

Work in small batches and mix to a thick pancake-batter consistency so the material holds on the trowel briefly before flowing off. Before applying, make sure the wood surface is a little rough—sanding with low-grit sandpaper helps the Ardex adhere. We applied a first coat focused on coverage, intentionally building a slightly thicker layer around edges to ensure solid protection during sanding.

After a few hours of drying, I scraped off drips from the bottom edge and sanded the top with an 80-grit palm sander. The goal of the first sanding was to knock down high ridges and smooth out rough spots before a final skim coat.

The second Ardex coat was mixed slightly thinner and applied more carefully for an even finish. Once cured, I sanded progressively with 80, then 120, then 220 grit to achieve a smooth surface ready for sealing.


Sealing the Concrete
For durability and a glossy stone-like look we used a high-gloss wet-look sealer applied with a small foam roller. Multiple thin coats provide the best protection and a reflective finish that highlights the white Ardex surface. We applied two to three coats and allowed the table to cure before bringing it into the living room.

After it cured, we sat it in place and finally had a functioning coffee table. The glossy white top contrasts nicely with the darker sofa and rug, while tying into other bright accents in the room like the bookshelf and curtains.

The finish retains subtle imperfections—light trowel marks and slight textural movement—which give the surface character and avoid that uniform, plastic-like appearance. Those small variations mimic the natural movement you’d get in real stone and are part of the handmade charm.

We’ve talked about a few finish options for the wooden base—staining the legs a bit darker to hide light edges or painting the base glossy white to match the top—but for now we’re just enjoying being able to put our feet up. The table feels solid, looks custom, and cost a small fraction of a stone replacement.

Since these photos were taken we’ve also painted and recovered two armchairs in the room, so the seating is even comfier. There are more tweaks to come, but this project proved that a DIY concrete-look top can be an affordable and attractive solution for a custom-shaped coffee table.
P.S. If you subscribe to project updates and weekly emails, you’ll get more DIY tips, design notes, and behind-the-scenes details about projects like this.
*This post includes affiliate links*








