Objectales

Popular

DIY Dollhouse Plans: How to Build a Miniature House

featured 47283

Update: You can check out Part 2 of this project right here.

how-weo-built-a-wooden-dollhouse

When Sherry and I first talked about building a dollhouse for Clara, I admit I felt intimidated. Not because dollhouses are scary, but because my imagination immediately pictured elaborate, to-scale Victorian replicas that seemed beyond my patience and skill. Once Sherry showed me her Pinterest inspiration—projects like Mousehouse, Natty Michelle and Under The Sycamore—I stopped sweating and actually got excited. Yes, excited about a dollhouse.

img 47283 2

Before building, I had to reclaim a bit of basement space. If you remember “this mess,” it was time for a quick tidy so I’d have a proper workspace for the DIY dollhouse build.

img 47283 3

I didn’t do a deep purge, but a quick cleanup gave me a usable area. It wasn’t a dramatic after photo, but it was enough to start cutting and assembling.

img 47283 4

With the workspace ready, we planned the dollhouse. Sherry claimed priming, painting, and decorating as her parts of the project, while I handled the design and construction. She casually suggested a three-story house with seven rooms, so I based our layout on the Under The Sycamore inspiration but adjusted the room arrangement to suit Clara’s play style.

We chose inexpensive 1 x 8″ white boards for construction: light, affordable, sturdy, and wide enough to make play easy. The plan called for 8″ ceiling height on the first two floors and a sloped attic that ranged from 6″ to about 10″. The finished dollhouse measures roughly 30″ tall by 30″ wide. We deliberately made the rooms a little taller than strict scale so Clara would have plenty of room to move toys and furniture.

img 47283 5

All wood materials for the build totaled about $35 (I already had nails). I began by cutting most pieces to size—everything except the roof pieces—creating a basic box about 30″ wide and 24″ tall. I cut the interior partition walls to 8″ tall and trimmed their sides slightly on the table saw so they fit neatly between the floors.

img 47283 6

To position the internal walls, I measured and marked the floor boards so each divider would sit precisely where I wanted it. The two marks on the board indicate the sides of each wall panel.

img 47283 7

I prefer screws for many projects, but for this dollhouse I avoided visible screw holes and the risk of splitting thin boards. I used wood glue plus small nails to secure everything. Wood glue can be messy and a little slow, but in this case it provided strong seams that worked well.

img 47283 8

I clamped scrap pieces to hold the walls steady while the glue set, which made nailing and alignment easier.

img 47283 9

Impatient as always, I carefully tipped the structure to drive nails through the base into the wall panels. This made the walls secure while the glue cured.

img 47283 10

After installing the first- and second-floor walls, the structure began to look like rooms instead of a pile of boards. I delayed adding the third-floor wall until I had the roof pieces ready, since the attic slope needed to align properly.

img 47283 11

I secured the side panels and interior walls to the floors using glue and nails, and I used a scrap block to keep corners square while fastening.

img 47283 12

For the roof supports, I cut the side boards with a shallow 15-degree angle on top so the sloped roof would rest evenly. That angle was mostly an aesthetic choice that worked well for our attic slope.

img 47283 13

I debated drawing exact geometric diagrams for the roof peak but decided to start simply: two 15-degree cuts joined together. The two roof pieces fit and glued together to form a tidy ridge.

img 47283 14

Once the roof assembly had cured, I used it as a template to cut the center support wall, then glued and nailed that piece into place as well.

img 47283 15

With the roof secured the project really started to look like a doll-sized house.

img 47283 16

I added a back panel from thin plywood scraps. The piece I used didn’t span the entire height, so I placed the seam behind the third-floor board to keep it hidden. I attached the back with glue and nails in the same manner as the rest of the structure.

img 47283 17

img 47283 18

For the roof top I pieced together a few scrap strips, which created seams we planned to hide with caulk and paint. That approach kept the build efficient and still delivered a seamless look once primed and painted.

img 47283 19

To improve stability I mounted the finished house onto a larger base—1 x 12″ cut to size and sanded with rounded edges. A few more dabs of glue and nails later, the construction phase was complete.

img 47283 20

img 47283 21

The whole build was surprisingly straightforward and took about three hours of work after an initial hour of clearing the basement. I’m already thinking about adding decorative, non-functional doors and windows to the back, but since Clara’s birthday was only days away, our priority was to get the house painted, furnished and wrapped as a gift.

Sherry takes over in Part 2 to cover priming, painting, furniture selection and decorating—the parts she rightly calls the “fun part.” I thought building it was the fun part, so clearly we make a good team. The dollhouse was a hit: Clara loves it, Sherry is thrilled, and even I find myself wanting to play with it now and then.

img 47283 22

Has anyone else built a dollhouse or created a custom play item for a child? We’d love to hear your DIY tips, favorite materials, or eBay furniture finds—dollhouse building is a great blend of woodworking and decorating that’s accessible to many DIYers.

Update #2: We created a “Shop Our House” page to help you find furniture and accessories you see in our projects, along with paint colors and sources.