DIY Scrap Wood Picture Frames: Step-by-Step Tutorial
DIY Simple Wood Frames from Scrap Materials
As Sherry mentioned in her Pinterest Challenge post this morning, we decided to make simple wood frames for her homemade artwork. Part of the motivation was cost—making our own frames from scraps is budget-friendly—and part of it was curiosity: how straightforward could this project be if we kept it basic?

We challenged ourselves to spend nothing and use only what we already had on hand. That boiled down to:
- leftover scrap wood
- wood glue
- a staple gun
- a hammer
- sandpaper
- a miter saw (or a miter box and hand saw)
- duct tape
- spray paint with primer built in
We started by rooting through my enormous basement pile of lumber to find pieces long enough to frame a spare canvas that was still wrapped in plastic. Using the canvas as a template helped us size the frames without measuring a lot, and kept the cost at zero so far.

The plan was simple: cut four boards with 45-degree miters and join them to form a rectangle. A power miter saw made the job quick; if you don’t own one, a miter box and a hand saw will do the trick—it just takes a bit longer. I cut matching sides two at a time, clamped together, to ensure parallel pieces were the same length and to speed up the process.

After making the first miter cut, I laid the stacked boards on the edge of the canvas to mark and trim the opposite end—slightly overlapping the canvas so the finished frame would rest on it. Keeping the boards clamped while cutting keeps the angles consistent.

With the two long sides cut, I repeated the same process for the shorter pieces: stack, cut a 45-degree angle, place on the canvas, mark, and finish the cut. In just a few quick passes I had all four corners mitered and the frame pieces ready to assemble.


We made two frames, each from different scrap wood. One set had a smoother finish, the other was knotty and rustic. Matching materials isn’t necessary for this easy look—variation can be part of the charm.

Before joining the pieces, I sanded the cut edges to smooth any rough spots. Then I applied wood glue to the mitered ends. I normally prefer mechanical fasteners, but for a no-fuss approach I wanted to see how glue plus a simple backing method would hold up.

Sherry suggested using a staple gun on the back to hold the glued corners together while they set. That gave the joints some immediate strength and made the assembly quick. Our upholstery-style staple gun did most of the job, and I tapped each staple flush with a hammer to make sure it seated fully.

When we turned the frames over after stapling, one looked slightly uneven. To reinforce the joints I ran a little more glue into the visible gaps from the front. I swapped to an Elmer’s bottle that was still fresh and let both frames rest for a couple of hours.

Once the glue cured, the frames were solid—no wobble. We sprayed them with Rustoleum paint-and-primer-in-one in satin white for a quick, even finish. Spray paint saved time compared with brushing on primer and paint separately, though either method works well depending on your preference.

For hanging, Sherry planned to use sawtooth hangers and we had some on hand, so no purchase was necessary. To attach the canvases to the backs of the frames we used duct tape—far from elegant, but quick, reversible, and free. That choice keeps the artwork easy to swap out later.

In the end we didn’t end up using the sawtooth hangers for one piece because it went over the stove in the kitchen instead of the office. For that location we chose Velcro-style picture hanging strips for a cleaner, removable mounting. We bought a small pack of those and a sheet of plexiglass to protect the canvas over the stove; between the two items the only out-of-pocket cost was about $3 each, so these frames were essentially free to make.

Have you built simple frames from scrap before? If so, what tricks saved you time or improved durability? For anyone trying this, the essentials are straightforward: accurate 45-degree cuts, sanding, glue plus a temporary staple or clamp, and a finish coat of paint. With a little patience and basic tools, you can create clean, custom frames without spending much—or anything at all.
Update: We finally created this Shop Our House page to help you hunt down any furniture/accessories that you see in our house, along with all of our paint colors.








