Objectales

Popular

DIY Shiplap Wall Plank Installation for $31

featured 91978

A while back we promised to share the DIY steps for this shiplap-style paneled wall treatment because it’s unbelievably simple and extremely budget friendly. In our case the whole job cost just $31—cheaper than dinner out or a couple of light bulbs. The result is a clean, wipeable, and durable backsplash alternative that works especially well when you want a subtle counterpoint to patterned tile.

Shiplap Planking Detail In Duplex Kitchen With Blue Cabinets

We used this treatment on the stove wall in each of the duplex kitchens because carrying the patterned tile across both walls felt visually busy. The planked paneling blends into the cabinetry and is easy to clean—perfect for rental kitchens that see heavy use. After a summer with dozens of renters, it still looks like new.

White Planked Wall In Duplex Kitchen With Wood Shelves

Some people call it planking, horizontal paneling, or faux shiplap. Real shiplap interlocks, but the look is the same: thin boards installed horizontally with small, consistent gaps between them. We liked the way designers use it in beachy and modern kitchens and finally decided to try it ourselves. In short: it’s easy, inexpensive, and gives big visual impact.

For this project we cut thin sheets of underlayment into strips, nailed them to the wall with small spacers to keep consistent gaps, then primed and painted the surface with a semi-gloss washable paint color-matched to the cabinets. Using 5mm underlayment instead of pricier pre-made shiplap boards saved a lot of money—under $2 per 8-foot strip versus $5–$6 for premade boards—without sacrificing durability.

Full Duplex Kitchen With Planked Wall And Pink Tile Backsplash

Cutting your own boards takes a little more work, but it’s straightforward. If you’d rather move faster and don’t mind spending more, pre-made boards come pre-primed and often have built-in spacing. We followed a budget-friendly approach inspired by other DIYers who used thin underlayment or bender board to achieve the same effect. Our material had a bit of visible grain compared to MDF, which we actually liked for added texture.

Nail Gun Securing Wood Panels To Backsplash Using Tile Spacers

Materials

We already owned most of the tools and only bought wood and paint for this job, so completing two kitchens cost us about $62 in materials. If you don’t already have the tools, you may need to invest in a few essentials that are useful for many other projects. Also note: if you have a gas stove, check local code—some areas require a metal strip behind the stove instead of wood.

What we used:

  • 4 × 8′ panels of 5mm underlayment (we ripped each panel into eight 8′ strips)
  • Primer (a quart is usually enough for a backsplash-sized job)
  • Semi-gloss paint (wipeable finish; color-matched to cabinets)
  • Wood filler for nail holes
  • Caulk for finishing edges
  • Paint brush and small foam rollers
  • Small spackle knife and sanding block
  • Nail gun and 1.75″ brad nails
  • Table saw or have the store rip strips for you
  • Miter saw or hand saw to trim strip lengths
  • Jig saw (to cut outlet and switch openings)
  • Drill/driver and a 1/2″ drill bit (to create starter holes for the jigsaw)
  • Stud finder, level, and pencil

Cut Your Boards to Size

Underlayment comes in 4 × 8′ sheets. Have the store cut them into manageable widths if needed, then rip the strips to your final width at home. We made our strips 5 7/8″ wide—leave a little under 6″ to account for material lost to the blade. Trim each strip to length for the wall; our wall was just under 8′ so each strip needed a small end cut.

Cutting Wood Strips In Half Along Table Saw For Shiplap Look

After cutting, sand the edges lightly to remove splinters so the boards sit flush and look clean.

Miter Saw Set Up To Cut Panel Strip To Length
Sanding Rough Edges Of Wood Panel Strip Using Sanding Block

Prep Your Wall

Remove outlet covers and switch plates, and locate studs so you can securely fasten the boards. Mark vertical stud lines with a long level as a reference. These lines will help you drive nails into studs as you install each strip.

Electrical Outlet Covers Removed Before Installing Paneling
img 91978 10
Long Level Used To Mark Vertical Lines On Wall

Cut Holes for Outlets & Switches

Hold each board in place and mark the outlet location. To ensure the outlet sits on top of the board edge (so the cover plate will be flush), mark both left-right and top-bottom positions and transfer those measurements to the back of the board. Drill 1/2″ starter holes in the corners of the cutout, then use a jig saw to cut the opening to size. Reinstall the outlet so it rests on the panel edge.

Electrical Outlet Screwed Back In Place Over Panel Strip
Panel Marked In Front Of Electrical Outlet
Height Of Electrical Outlet Marked Using Scrap Wood Panel
Lines Marked For Cutting Hole For Electrical Outlet
Cutting Hole In Back of Wood Strip using Jigsaw

Nail Your Boards to the Wall

Start at the bottom and work your way up, using small spacers (tile spacers, pennies, or anything consistent) between boards to maintain even gaps. Secure each board with brad nails driven into studs. Some people use construction adhesive for extra hold—especially in high-humidity spaces like bathrooms—but we skipped it here to avoid damaging drywall if we ever remove the panels. The boards have held up well without adhesive.

First Two Panel Strips Installed Using Nail Gun and Green Tile Spacers
Nail Gun Securing Wood Panels To Backsplash Using Tile Spacers
John Standing On Ladder Nailing Wood Paneled Backsplash In Blue Kitchen

Prime, Patch, and Paint

After installation the raw panels looked great, but we wanted a wipeable finish that blended into the cabinets. Start by brushing primer into all the seams and then roll the whole wall with a small foam roller. Once the primer dries, fill nail holes and any wood knots with wood filler, sand smooth, then apply a second coat of primer if needed.

Shiplap Paneling Complete In Blue Duplex Kitchen

Finish with a semi-gloss paint in the color you chose. We had a paint sample scanned to match the cabinets so the wall would read as part of the cabinetry system rather than compete with our tile and chimney. After the final coat dried we caulked the perimeter where the panels meet the countertop and cabinets for a clean, finished look.

img 91978 21
img 91978 22
img 91978 23
Shiplap Planking Detail In Duplex Kitchen With Blue Cabinets

We repeated the process on the other kitchen and finished both installations over a weekend. It’s a fast, affordable way to add character and durability to a backsplash or accent wall.

img 91978 25

This method gives a polished, durable result without breaking the bank. If you want a subtle, easy-to-clean wall treatment that complements tile or other focal points, horizontal planking with thin underlayment is a great option.

Detail Of Planked Wall In Duplex Kitchen With Counter Microwave

If you enjoy budget-friendly DIY projects, other reader favorites include a simple board & batten installation, easy landscape lighting, adding crown molding to cabinets or rooms, installing a subway tile backsplash affordably, refinishing furniture, and installing under-cabinet lighting. These projects offer big impact for relatively small investment and are great next steps if you want to keep tackling home improvements.

P.S. See our Home Improvement category for more step-by-step projects and ideas.