DIY Wood Kitchen Shelves: Step-by-Step Guide
Okay, let’s get some open shelves installed in this kitchen.

With the hood cover now built, we were finally ready to install the shelves around it. We initially planned to build true floating shelves (we even considered following a popular set of instructions), but after revisiting our inspiration photos we decided to be open to using brackets instead. If you’re wondering about dust and grease on open shelves, we researched it: with a good range hood and by storing frequently used dishes up front, open shelving can work well. Rarely used items get dusty in cabinets too, so the key is having solid ventilation and using what’s on display regularly. We’ll report back on how ours hold up.
Besides liking the look, brackets eased worry about mounting into our tiled wall — drilling into tile always gives us pause. We’d also heard Home Depot carries a range of affordable, attractive bracket options, and we narrowed it down to a few choices before picking our favorite.

We both agreed on the last option, so I bought a dozen of those brackets and some 12″ framing lumber to use as shelf boards. Several readers noted that 12″ framing lumber with brackets worked well in their kitchens, and we’d had success with a similar setup on our office desk, so it felt like the right approach.

One hiccup: 12″ framing lumber is actually closer to 11.25″ in finished width, which meant our 12″ dinner plates overhung the shelf edge. That overhang didn’t look great, so we considered our options.

Rather than buying new plates, we decided to add 1×2″ trim to the exposed shelf edges, the same finishing trick we used on our homemade console table. The trim would deepen the shelf to eliminate the overhang and cover the rough cut ends of the boards for a cleaner, more finished look.

Not only did the trim solve the depth issue, it also gave us a smooth edge to paint and finish. We liked the aesthetic improvement immediately.

Our material cost came to about $116 for brackets, $15 for the shelf boards, and $10 for the trim — roughly $141 total. That’s a reasonable investment for four shelves (two larger and two smaller), which is roughly equivalent in storage to three upper cabinets that would typically cost much more. Considering the money we saved elsewhere—reusing cabinets, building a fridge cabinet, installing tile ourselves, and sourcing a range hood secondhand—we were comfortable spending a bit more on shelving. We also already had paint and primer on hand.
Next we measured and marked everything. To locate studs we used a weighted-thread method tied to ceiling marks, the same approach we used to hang our range hood. The stud spacing lined up nicely for even bracket placement, except at one end where the hood’s mount occupies the stud. For those spots we planned to use heavy-duty anchors set into the tile.

We also cut the shelf boards to size. Some pieces look short in photos because we planned to add trim to the exposed ends, and the hanging threads you see in the images were our stud markers — not permanent marks on the tile.

We opted to trim only the exposed sides so each shelf would have the appropriate finish depending on its position. The long top shelf, backed by the wall and hood, needed trim only on the front. Other shelves required trim on one or both ends. Although that created different configurations, past projects taught us that once primed and painted the result would read as cohesive. We adjusted the raw board lengths so every shelf would finish at the same overall depth and length after trim installation.

We attached the trim with wood glue and finish nails, and I drilled a few pocket holes on the underside of the shelves thinking we might fasten the boards to the wall in addition to anchoring them to the brackets for extra stability.

That night I used wood filler to smooth the seam between the trim and the shelf board so the joint would disappear after priming and painting. Even before paint it was clear the trimmed shelves looked more finished and intentional—another win from solving that plate overhang problem.

While preparing the shelves we also set up to hang the brackets. We used 1×2″ scraps taped level as temporary shelf guides so we’d know exactly where the top of each bracket needed to sit.

The new brackets have two metal keyhole hooks on the back. To ensure precise placement we made a simple paper template for each bracket, taping the paper to the bracket, pressing it to the tile, and puncturing the holes so we could mark drill points without repeatedly handling the bracket. This made drilling into tile more controlled and less nerve-racking.

After transferring the hole marks to the tile we drilled pilot holes and installed anchors or screws where needed. Repeating the paper-template step for all brackets took time, but it ensured consistent, level placement across the run of shelves.

Once all the screw pairs were in place, we hung a test bracket to confirm the screws were the correct depth and felt secure. The fit was good, and the brackets sat flush and sturdy against the tile.

Before final assembly we decided to prime and paint the shelves and hood, so we paused with brackets hung and waited for primer to dry. Painting now avoids having to tape off grout lines or worry about paint on the tile later. We’ll apply two coats of the same cabinet color we used elsewhere, let everything cure, and then hang the finished shelves for good.

Once the paint is cured it should be a quick job to sit the shelves down on the brackets and secure them. We expect to have completed photos ready soon, barring the usual household chaos that accompanies any renovation. How about you—any projects, priming, or drilling through tile on your weekend?

We’re excited to see how these open kitchen shelves perform — both functionally and visually. With solid brackets, properly trimmed boards, and a careful paint job, they should add useful storage and a clean, modern look above the range area.









