DIY Wood Range Hood Cover: Step-by-Step Build Guide
DIY Lightweight Wood Range Hood Cover: How We Built It
We were ready to hide our exposed range hood and give the kitchen a cleaner, more finished look. For placement, we followed the manufacturer’s recommendation for height—JennAir suggested a range, and we mounted the hood 34″ above the counter, which fell right in the middle of that guidance.

To decide on the final shape and proportions, I mocked up two design options in Photoshop. Our first idea mimicked several inspiration photos we liked; it featured square panels on the front created with trim. After comparing the two mockups, we felt that design looked a bit top-heavy, so we moved to the cleaner option we preferred.


Once we committed to the look, I sketched a scaled plan on paper to work out dimensions. I also began calculating the wood and materials I would need. My three goals were simple:
- Build a sturdy structure using moisture-, steam-, and grease-resistant plywood so it will last
- Keep it as light as possible so it doesn’t add unnecessary weight to the wall
- Create a clean, attractive finish that fits the kitchen

With plywood panels and 1×2 boards in hand, I started from the bottom up. The base frame was three pieces of 1×2 screwed together in a U-shape using a Kreg Jig. I added pocket holes so I could fasten the frame to the solid wood plank we used to mount the hood—this gave the frame a secure anchor and took advantage of the overhang we already had in place.


The wooden cover does not touch the metal hood itself; instead the surround essentially floats around it. Our efficient range hood vents upward as intended, and the wood surround should tolerate normal kitchen conditions just like wood cabinetry does when installed near cooking areas. Since many people have built similar wood covers with no issues, we felt confident in this approach.
Note: early photos show duct tape on the vent joints. We replaced the duct tape with metal foil tape to meet venting best practices and avoid issues with heat and airflow.

After the frame was secured, I attached thin plywood panels to form the first three sides. I left a small gap around the front to allow access to the hood controls—just enough space for a finger to reach the buttons while keeping them mostly hidden.



For the next tier, which slopes toward the front, I built a slightly smaller 1×2 frame and beveled the top edge on the table saw so the angled plywood would seat smoothly. The angle was an educated guess rather than a laser-measured cut—sometimes a visual fit works perfectly in practice.


I added a thin strip of 1×2 to give the sloped plywood a nailing surface, then cut the adjacent side panels to match the exact angles. Marking the pieces in place and cutting them on the table saw produced clean, fitted quadrilateral panels that bolstered the shape of the surround.


The final tier became the chimney cover that hides the vent pipe. I built a compact 1×2 frame and firmly screwed it into ceiling joists. One hitch: the hole for the vent pipe was larger than expected, so we’ll need to patch the ceiling gap and later add crown molding to finish the look.



With the plywood panels in place, the major construction was complete. The hood was covered, the controls remained accessible, and the structure felt secure. Visually it still seemed a bit unfinished, but that’s where trim and paint transform the project.

To keep the hood light and easy to install, I used lightweight trim plywood and glued the trim pieces in place to avoid excessive nailing into the cover. I used a durable construction adhesive for most pieces and reinforced with tape during curing. Later I switched to a stronger adhesive that held pieces fast without shifting, which made final assembly quicker.

The top trim took longer because I ran out of material midway and had to pick up more. We chose not to add decorative trim around the chimney section since it’s primarily a functional cover and didn’t have visible seams needing finishing. Once we patch the ceiling hole and install crown molding, the chimney will blend in with the rest of the wall.

There are a few finishing steps left—priming and painting the surround along with the open shelves we’re building, and adding some caulk to make seams seamless—but overall I met my three goals: it’s sturdy, lightweight, and attractive.

This DIY surround won’t have every professional feature, but once primed and painted with a durable cabinet-grade paint, it should perform like a painted cabinet next to a hood. It was also much less expensive than custom or retail options—materials for the surround were modest, and the hood itself was an affordable Craigslist find. All told, the cost was a fraction of some of the high-end retail offerings.

We took after photos while the kitchen was still tidy—there’s still crown molding, shelving, paint, and other finishing touches to add—but it already breaks up the tile expanse and gives the room more character. Next on the list: patch the ceiling, paint, and hang the open shelves.



Have you ever built a range hood cover or wood surround? If not, this project shows how achievable it can be with basic tools, careful measuring, and an eye for proportion—plus a little patience for trim and finishing. We’re excited to finish the final details and share the completed look.








