How to Build a Deck: DIY Step-by-Step Guide
The deck is officially finished — cue the celebratory cowbells. I wrapped up the last work on Friday and spent the following days nervously waiting for the county inspection before I allowed myself to celebrate. The inspector arrived yesterday afternoon and — ta‑da — we passed. A huge sense of relief washed over me, not unlike the sweat I shed building the thing (note to self: build decks in spring or fall).

This is a massive upgrade from the tiny, rotting balcony we started with:

We wanted the deck finished before Sherry’s mom arrived from New York, so I hunkered down and pushed through the final stretch. It turned into more of a marathon than expected. We assumed three to four weeks of on-and-off work, but heat, thunderstorms, inspections, equipment rentals, material deliveries, summer travel, and the fact that I was mostly a one‑man crew with no prior deck experience stretched the project to ten weeks. Still — the victory feels just as sweet.

Despite the slog and the extreme weather, I actually enjoyed having an excuse to be outside and tinker during Clara’s naps or on Saturday mornings. It was peaceful to step away from emails and chores for a few hours and just saw and build. My dad’s help with the auger for digging post holes was invaluable — a true father/son project.

If you’re wondering how long a deck might take, an experienced crew could probably complete a deck like this in about a week, accounting for local inspection pauses. For a first‑timer working mostly alone and fitting work around other commitments, expect a month or two depending on weather and inspection timing. One guarantee: the satisfaction of sinking that final screw is enormous.
Here’s how I handled the stairs and railing. After laying down all the decking, I cut and attached the remaining posts.

Even though the stairs came next, I installed the railing posts first so I could plan the stair stringers — the diagonal boards that support the treads. You can buy pre‑cut stringers, but I cut my own to match the lumber we received and save cost. Figuring lengths and angles felt intimidating until I used an online stair calculator to handle the math, which made the process far easier.

With the rise (height of each step) and run (depth of each step) calculated, I used a simple marking trick from a how‑to video: clamp a straight edge to a framing square at the measured rise/run intersection to create a perfect guide for marking cuts on a 2 x 12.”

I cut along those lines with a circular saw, then finished the corner cuts with a reciprocating saw because a circular blade can’t always reach the tight triangular corners.


After testing the first stringer for fit, I used it as a template to mark and cut two more. For a 48″ wide staircase I used three stringers.

One stringer developed a small defect around a knot, so rather than re‑cut a whole board I patched it with a short piece of wood secured to the tip, checking first that the repair met code.

I attached the stringers to the deck using angled hangers and made sure each step was level as they ran down. To keep the tread spacing consistent, I installed blocking between stringers using equal‑sized scrap boards; they’re out of sight once the treads are in place but they prevent the steps from subtly narrowing or widening.



Next I set the posts that support the staircase in the middle and at the bottom, seating them on anchors set in concrete in the footing holes I’d dug earlier. I carefully marked anchor placement to align with the stringers, set the anchors in wet concrete, and allowed them to cure before raising and bolting the posts.


While the concrete cured, I cut the tread boards. To match the deck surface I used two 2 x 6 boards for each tread (including a small overhang) and a 2 x 8 board as the riser backing.

With posts set and bolted to the stringers, I loosely laid out the tread boards to confirm fit, then permanently screwed each board in place — a slower, screw‑heavy step than I expected.



Once the steps were installed I focused on the guardrail. The bottom and top rails were 2 x 4 boards spanning between the posts. Our county requires a maximum 4″ sweep space between deck surface and rail, so I used a 4 x 4 post as a spacer to keep the rail height consistent while fastening it.

Attaching the stair railing required careful measurement to meet code for bottom clearance and height relative to the tread nose. Cutting the angled rails and holding pieces in place while screwing them together was fiddly, but it all came together.

You might notice the posts attached to the deck were replaced and temporarily left taller. I initially cut them too short to meet the required railing height on the steps, so I replaced them and decided to trim them to final height only after confirming they passed inspection — lesson learned.

The balusters (vertical pickets) went in next. We considered a more modern or elaborate design but chose a traditional look to match the patio railing and fence visible from the living room. That decision kept the process straightforward and ensured visual continuity.

The top rail cap — a 5/4 x 6 decking board — was the final guardrail component. Cutting the notches and angles around posts took patience, but the finished cap provides a clean, comfortable ledge.


For the stair railing balusters I left them slightly long, installed them, then removed the rail cap and trimmed the tops with a reciprocating saw so the cap would sit flush for a finished edge.

I also installed the required handrail because our stairs have more than three steps, and added decorative post caps at the top and bottom of the staircase. They attach with a little caulk and instantly make the posts look finished.



Seeing the finished deck still makes me proud. I couldn’t resist texting my mom — and a few close friends — to share the news.



Being county‑approved doesn’t mean the job is completely finished: we still need to seal the deck and furnish it. Once we choose the right sealer and complete that step, we’ll share a full budget breakdown. For now, you can find me sitting on the deck, without furniture, enjoying a cold soda and promising Sherry I won’t build another deck for at least ten years. The renovation of our first house bathroom still ranks as my hardest project, but this deck comes in at a close second — and it feels great to check it off the list.
Psst — Want all the deck details? Here’s where we shared our vision for the space, removed the plantings and old balcony, selected materials, documented the first day of building, dug post holes, navigated inspections, set posts, installed joists, prepared and laid decking, and tracked every step of the process.








