Objectales

Popular

How to Build Built-In Bunk Beds: Step-by-Step Plans

featured 85554

We’re excited to share the finished built-in bunk beds we installed in the small bunk room at our beach house. At roughly 7 feet wide, the room is compact, but by building custom, wall-to-wall platforms we fit two Twin XL mattresses and created a sturdy, playful space the kids love for sleeping, reading, and hanging out.

built in bunk beds in a small room with children on each bed

I admit I felt more nervous about this project than about building a bookcase or table — these bunks literally float off the walls, and the top holds someone right above another person (and the occasional chihuahua). The good news: the design is extremely solid and surprisingly straightforward to build when you secure the platform frames into the studs.

diy built in wall to wall bunk beds with chihuahua on bottom bunk

This guide covers the complete process from framing to finish:

Steps For Adding A Built-In Bunk Bed

Below is an overview of what we’ll walk through in more detail:

  • Building a platform for the bottom bunk
  • Securing a floating platform for the top bunk
  • How to choose bunk height and mattress spacing
  • Installing the ladder and safety railing
  • Adding trim, molding, and finishing touches
detail of bottom bunk of built in wall to wall bunk beds

This room measures 81″ across, which made it ideal for an 80″ Twin XL mattress. Once we realized the dimensions during renovation, building wall-to-wall bunks became an obvious, high-impact choice. For a while the space just held a mattress on the floor, but now it’s a proper bunk room.

before shot of mattress on floor in bunk room

Here’s how we built these built-in bunks, step by step.

Materials & Supplies Needed

The plan uses two floating platforms attached to the wall studs. Because the room is narrow we were able to anchor three sides of each platform directly into studs, providing great strength without vertical posts. Key materials and tools included:

  • 2×4 boards
  • 1/2″ plywood panels (platform tops)
  • 1/8″ plywood panels (underside of upper platform)
  • Primed 1×8 boards
  • 2×2 pine boards (for ladder and railing)
  • Primed lattice strips
  • Baseboard (reuse existing if possible)
  • 4″ and 5″ structural screws
  • Miter saw
  • Circular saw
  • Power drill
  • Nail gun
  • Stud finder
  • Bar clamps
  • Pocket hole jig (optional)
  • Long levels

Our material cost for the build was about $250 (excluding mattresses and bedding), thanks to keeping the design simple and anchoring into studs.

Step 1: Build The Bottom Bunk Bed Platform

We initially framed the bottom platform directly on the floor to maximize headroom. Later we raised it a few inches for aesthetic reasons, but the in-place framing approach remained the same and made the tight fit easy to manage. Building in place also avoids wrestling large frames around in a small room.

building base frame of bottom bunk around walls

Start by cutting 2×4 pieces to fit wall-to-wall for the back and sides, then add cross braces spaced roughly every 12″. These cross members support the plywood and keep the frame rigid. We joined pieces with pocket holes and screws for a tight connection.

drilling pocket holes using kreg jig into 2x4s

Once the frame was complete we installed 1/2″ plywood on top, cutting to size and ensuring any seams land on cross braces. A nail gun made quick work of securing the panels.

adding plywood to create base of bottom bunk bed

After seeing it in place, we raised the platform a few inches to allow for baseboard and a cleaner built-in look. We added short 2×4 legs under the platform and a front 2×2 to give a nailing surface for trim.

bottom bunk reconstructed to float off of the floor

Raising the platform looks more complicated than it was — the structure stayed simple and robust thanks to good bracing and stud attachment.

Step 3: Choose A Height For Your Top Bunk

With an 8-foot ceiling, our priorities for bunk heights were:

  1. Roughly equal headroom for both bunks
  2. Enough clearance on the bottom bunk for an adult to sit up comfortably
  3. A snug top bunk to discourage jumping or standing
John measuring height and placement of top bunk

We set the top bunk a bit higher than the midpoint of the room to meet those requirements. This choice also made the lower bunk adjustments straightforward.

Step 4: Build Your Floating Top Bunk

The upper platform uses the same framing method as the bottom, but relies on heavy-duty structural screws driven into studs to support the floating frame. These structural screws are excellent for pulling 2x4s tightly into studs without the fuss of lag bolts, and a good power drill is all you need to install them.

rss rugged structural screw box from Home Depot

Bar clamps were invaluable for holding the frame tight to the wall while we drove screws into studs. After securing the three wall-facing sides and attaching the front, we installed 1/2″ plywood for the mattress base and tested the platform’s rigidity.

John sitting on top bunk to nail plywood into floating platform

With both platforms framed and secured, the structural work is complete and it’s time to refine the appearance.

Step 5: Adding Trim & Molding

We covered exposed framing with pre-primed 1×8 boards along each platform front and reinstalled baseboard across the back wall. Adding 1/8″ plywood to the underside of the top bunk and framing seams with lattice strips gives a finished, built-in look. All trim was attached with nails and wood glue for a long-lasting hold.

white trim pieces added to the face of bunk bed platforms

Once painted to match the room trim, the platforms blend seamlessly into the space.

Step 6: Build Your Ladder

For a clean, modern ladder and railing we used 2×2 square pine boards. Each ladder rung is 18″ wide, and we kept consistent spacing using scrap blocks as temporary spacers while attaching rungs. The rungs were secured into the verticals with structural screws and then doubled up later to provide a wider step underfoot.

bunk bed ladder pieces laid out in hallway for construction

We sanded the edges to a soft square profile so the ladder feels good in hand and is safe for kids.

Step 7: Attach The Ladder & Build The Railing

Clamp the ladder into position, secure it to the frame with structural screws, and install the top rails. We attached one top rail into the ladder and the opposite rail into a short vertical 2×2 post, then added a middle rail for added safety. Countersinking screws and filling with wood putty can create an even cleaner look if desired.

clamps holding diy bunk bed ladder and railings in place

After staining, the hardware blended nicely with the wood tones, giving an industrial touch that we liked.

Step 8: Stain The Ladder And Railings

We matched the ladder finish to our floors using a multi-step staining process: a pre-stain conditioner, a light coat on raw-cut ends to prevent dark blotches, an overall base stain wiped off after a short wait, and a final light glaze to add warmth. Testing on scrap wood is essential to dial in the exact tone you want.

Sherry applying stain to bunk bed railing for raw wood look

The layered approach gave us a balanced color that complements the room and the floors.

Step 9: Add Mattresses & Bedding!

With paint and stain dry, we added mattresses and bedding and revealed the finished bunks to the kids — and Burger the dog. The new bunk room quickly became a favorite spot in the house for naps, climbing, and nighttime stories.

diy built in wall to wall bunk beds with dog on bottom bunk

We later added a small cubby organizer for clothes and toys since the space is used mainly for weekend and summer stays — it’s the perfect compact solution for a beach house.

view into small room bunk beds with cubby organizer baskets under window

Final Measurements For Our Built-In Bunk Beds

Here are the exact measurements we used for this build:

  • Platform dimensions: 81.5″ x 40″ (fits an 80″ x 38″ Twin XL mattress)
  • Bottom bunk: platform top is 10″ off the floor, mattress top is 17″ off the floor, with 34.5″ headroom
  • Top bunk: platform top is 56″ off the floor, mattress top is 63″ off the floor, with 32.5″ headroom
  • Ladder: rungs are 18″ wide (ladder is 21″ edge-to-edge); rungs spaced 12″ top-to-top
  • Top railing: 7″ above mattress top (code typically requires 5″ minimum); the rails have a 3″ gap between them
diy built in beds with raw wood railing and ladder in a small room

Overall, the build was far less nerve-wracking than expected. Anchoring platforms into studs with structural screws and keeping the frame simple means you can build safe, attractive built-in bunk beds even in a very small room. If you want the look but prefer fewer steps, consider hiring a carpenter for the structural attachments and finishing the trim yourself.

For other built-in and storage projects we’ve shared: Built-in Pantry Shelves; DIY Storage Shelves for a Shed or Garage; Floating Shelves in a Bonus Room; Wall-to-Wall Built-in Bookshelves Around a Doorway.

*This post originally referenced products and tools used in the build.*