Objectales

Popular

How to Convert an Over-the-Range Microwave into a Range Hood

featured 62669

Installing an Affordable Over-the-Range Hood: Our Easy DIY Swap

For the past few weeks our kitchen has felt like a game of hide-and-seek with the vent hood: hood, there it isn’t. We removed the over-the-range microwave while painting the kitchen and planned to replace it with a 30-inch gas cooktop. The microwave was the only appliance we intended to change during Phase 1 of our kitchen makeover because it dominated the space above the stove and didn’t vent as effectively as a dedicated range hood. We moved the microwave to the countertop temporarily and plan to relocate it to the pantry long-term once an outlet is added, but that left us without over-stove ventilation.

img 62669 1

Because this was intended as a temporary solution until Phase 2—when we may install an exposed hood—we didn’t want to pay much. We’d seen several used hoods on classifieds for under $30, which was a sensible price for something we could resell later. When a clean, white unit that matched our stove size and offered top-venting showed up for $25, we decided to go for it.

img 62669 2

The only drawback was that the hood didn’t include mounting hardware and was designed to be hung under a cabinet, so we would need to improvise a secure mount—something we’d done before with another Craigslist find. Still, this install turned out to be much easier than expected thanks to a few fortunate alignments in the existing ducting and wiring.

img 62669 3

The hood could vent out the top or the back, and the rectangular exhaust opening on the hood lined up perfectly with the rectangular vent inside the cabinet. That made the duct connection straightforward. I sealed the unused rear opening with proper foil HVAC tape (not common cloth duct tape) to ensure a tight fit and reduce leakage.

img 62669 5

Luckily, electrical wiring was already routed through the wall to the right location, so we didn’t need to call an electrician. I removed a small metal knockout on the hood to create an access point so those existing wires could be pulled into the hood’s electrical box for connection.

img 62669 6

The cabinet had a small front lip that prevented screwing the hood directly to the cabinet bottom. To solve that, I constructed a simple scrap-wood sandwich: two wooden blocks mounted inside the cabinet on either side, providing a flat surface to secure the hood so it would sit flush when viewed from the front.

img 62669 7

img 62669 8

The trick that made the install painless was discovered in a how-to video: use a temporary support to hold the hood in place while you fasten it. I clamped a thin 1×2 scrap board across the cabinet opening to support the hood’s weight while I worked. It required removing one cabinet door briefly, but that small step prevented any awkward balancing acts and saved a lot of sweat and swearing.

img 62669 9

In the video another tip shows temporarily screwing a brace to the back wall for extra support. I didn’t need that here; once the hood rested on the board and against the newly installed wooden blocks, it stayed put. I checked from inside the upper cabinet to confirm the duct lined up with the hood’s exhaust port and then sealed that joint with more foil HVAC tape for good measure.

img 62669 10

With the hood supported, I tightened screws through the hood’s keyhole slots into the wood blocks (accessible by removing the grease filters). After securing four screws—front and back on each side—I completed the electrical connections inside the hood’s junction box and reinstalled the filters.

img 62669 12

img 62669 13

The whole process took about 45 minutes, most of which was cutting scrap wood for the mounting blocks. It’s not a fancy install, but for $25 and under an hour of work we regained ventilation above the stove and removed the visual bulk of our old over-the-range microwave. We plan to sell that microwave for at least what we paid for the hood, so this Phase 1 change stays budget-friendly.

img 62669 14

One of our favorite features is the halogen lights on the hood. Until we install dedicated under-cabinet lighting, these make a noticeable difference by casting a bright, focused glow over the stovetop and counter.

img 62669 15

In short, this corner of the kitchen went from feeling cramped and microwave-dominated to open and ventilated. The new hood sits cleanly above the stove and improves both function and appearance.

img 62669 16

img 62669 17

Next up we’ll hang floating shelves along the sink wall and tackle cabinet painting—projects we hope to complete over the holiday break so the new year brings a refreshed kitchen. If you’re considering swapping a vented microwave for a dedicated hood, this install shows that with a little planning, basic tools, and some scrap wood it can be straightforward and inexpensive.

Did you replace a vented microwave with a hood? Was your project complicated or surprisingly easy? It’s always a relief when a task you worry about turns out to be manageable—far better than projects that fall apart halfway through.