How to Install a DIY Sprinkler System for Your Lawn
Tired of wrestling with hoses, sprinklers, and timers to keep your lawn green? Or watching grass brown under the summer sun? You can install an automated in-ground irrigation system yourself. It requires planning, patience, and elbow grease, but doing it yourself saved us hundreds of dollars. Below is a clear, practical guide to how we completed our DIY sprinkler system.

Before the step-by-step instructions, here are a few considerations to help you decide whether to DIY or hire a pro.
Should You DIY Your Sprinkler System?
I’m proud of finishing this project, but one honest takeaway: large, oddly shaped yards are challenging DIY projects. Our yard’s size and layout extended the work and increased the physical strain. A professional crew could have completed the job in a day or two; it took me over three weeks. That said, we saved roughly $1,700 compared to a professional quote and now have the confidence to troubleshoot or adjust the system ourselves.

Smaller yards or garden beds are usually better DIY candidates, and a drip irrigation system is especially easy to install for flower beds and borders. Large systems require repetitive digging, pipe fitting, gluing, and a fair amount of strength and stamina.

Even so, the long-term convenience of a reliable irrigation system and the money we saved made it worthwhile for us. Plus, a well-installed system reduces watering time and ensures deep, consistent irrigation.
Why Install a Sprinkler System
A sprinkler or irrigation system keeps lawns, gardens, and planter beds healthy by providing consistent, deep watering. Compared to manual watering, automated systems save time and reduce the risk of under- or over-watering. Modern controllers allow zone-based scheduling, run smart programs that adapt to local weather, and can be wifi-enabled for remote control.

We planned ours alongside a landscaping redesign and paid $300 for a landscape architect plan. She advised planning irrigation before purchasing plants because our yard gets intense sun. After getting a few professional estimates (around $3,500), a neighbor who had installed systems before offered to help, and we began the project last September.

Below are the steps we followed to complete our irrigation installation, organized so you can replicate the process efficiently.
Steps to Installing a Sprinkler System
Quick overview of the main steps. Each is described in more detail below:
- Get a companion meter
- Plan your layout
- Call 811 to mark utilities
- Buy supplies
- Dig trenches
- Lay pipes
- Install valves
- Install a backflow preventer
- Add sprinkler heads
- Wire everything together
- Program and finish
Step 1: Get a Companion Meter
Many municipalities offer a companion (secondary) water meter for irrigation or pools. Your primary meter often charges for water use plus wastewater/sewer fees. Since sprinkler runoff doesn’t return to the sewer, companion meters are typically billed only for water use, which can lower utility costs over time. In our county, the water department installs companion meters after a $500 application fee and a waiting period of a couple of weeks. Start this process early if your locality requires it.
Step 2: Plan Your Layout
A smart layout saves time and money. Identify where water (companion meter) and power (controller location) will come from first. From the main water line you’ll branch to individual zones. Zones group sprinkler heads to manage water pressure and tailor watering to different areas—sunny vs. shady, lawn vs. beds.
Map your main line and zone lines, then walk the yard to place each sprinkler head roughly 8–10 large steps apart. Mark locations with flags. You can adjust spray arcs later to avoid overspray on driveways, decks, or wooded areas.

Step 3: Call 811
Before digging, call 811 to have utility lines marked. Even shallow trenches can encounter buried utilities, so this is an essential safety step.
Step 4: Buying Sprinkler System Materials
With a layout in hand, purchase supplies. Typical items include:
- Sprinkler heads (for lawns)
- Mister heads (for flower beds/mulch)
- 1/2″ swing pipe (flexible “funny pipe”) for each head
- Swing pipe elbows (two per head)
- 3/4″ x 3/4″ x 1/2″ threaded tees for branch connections
- 3/4″ valves — one per zone
- Valve boxes for each valve
- 3/4″ and 1″ PVC pipe for zone and main lines
- Assorted PVC connectors, primer, and cement
- Controller with enough zones (we used an 8-zone smart controller for our 6-zone yard)
- Underground sprinkler wire with multiple colored conductors
- Backflow preventer if required by your local code
- Digging tools or trencher rental
Understanding how components fit together makes the list less intimidating. Below are concise explanations of the main parts and how they connect.
Sprinkler heads and connections
Most sprinkler heads sit mostly underground and pop up when pressurized. Each head connects to the zone line (3/4″ PVC) via a short length of flexible swing pipe. Use a swing pipe elbow at the head and a threaded elbow at a tee on the zone line. The flexible pipe makes precise placement easy, especially around curves and landscaping features.

Valves and controller
Each zone is controlled by an electrically actuated valve installed at the start of the zone line and set inside a valve box for protection and access. The valves are wired to a central controller that schedules and operates watering cycles. Choose a controller that accommodates your number of zones; smart wifi controllers can automate schedules based on weather and send alerts if issues arise.

Wire, pipes, and other supplies
Use underground-rated multi-conductor sprinkler wire so each zone has a uniquely colored conductor. The backflow preventer is an above-ground safety device required by many municipalities to stop irrigation water from flowing back into the public supply. For main lines use 1″ PVC and step down to 3/4″ for zone runs as needed. Estimate PVC lengths from your layout and get necessary fittings and tools like a PVC cutter, primer, and cement.

Step 5: Dig Trenches
Trenching can be physically demanding. Call 811 first and use caution around utility lines. For compact areas near utilities or sidewalks, hand-digging is safer. For larger runs, we rented a trencher for $88/day. Trenchers are heavy and require careful handling; consider borrowing help for loading and operating. In tight spots we hand-dug and used a mallet to shove pipe under sidewalks.

Step 6: Lay Your Irrigation Pipes
Lay PVC in the trenches and assemble using primer and cement. Apply primer to both mating surfaces, wait a few seconds, then apply cement and press together with a slight twist, holding for about 30 seconds. Use a ratcheting PVC cutter for clean cuts. This step is repetitive and can be physically taxing, especially when working hunched over or in tight spaces.

Step 7: Install Your Valves
Install a valve at the start of each zone, placing it in a valve box and orienting it in the direction of water flow. Connect the valve plumbing using threaded couplings with plumber’s tape for leak-free connections. Valve wiring is done later after all plumbing is complete.

Step 8: Install a Backflow Preventer
A backflow preventer prevents irrigation water from re-entering the public water supply and may be required by your county. Installing it can involve tricky connections to existing mains. I encountered leaks when connecting PVC to the county copper pipe and ultimately needed a plumber. Also confirm local code requirements: you may need a shut-off valve before the backflow, couplings to remove it seasonally, and the system blowout connection located after the backflow device.

Check local codes and, when in doubt, consult a licensed plumber or inspector before finalizing the backflow installation.
Step 9: Add Sprinkler Heads
Install threaded tees where each sprinkler head will connect, attach short sections of swing pipe, and screw a swing elbow into the tee and into each sprinkler head. Pre-assemble swing pipe pieces and nozzles indoors to speed the job. Set heads low to avoid mower strikes and adjust spray arcs once the system is pressurized. This step can be tedious if you have many heads—take your time to ensure correct spacing and coverage.

Step 10: Wire Everything Together
Run underground-rated multi-conductor wire from the controller to each valve. In the controller, assign one conductor per zone and a common wire. Run the main wire alongside your main trench, leave extra slack at each valve, and use waterproof wire connectors to join valve leads to the appropriate colored conductors. Keep a consistent color scheme so you can identify zones later. Leave a couple of unused conductors if you anticipate future expansion.

Step 11: Final Testing and Finishing Touches
Test every zone for leaks, check pressure, and adjust spray arcs and nozzle types for uniform coverage. Program your controller with appropriate run times and schedules; a smart controller can automatically adjust based on weather. After testing, backfill trenches and repair turf. You may need to reseed or lay sod to restore disturbed areas.

For us, the DIY installation cost approximately $1,800 including tool and truck rental—about half the professional estimate. The savings were worthwhile, though the physical toll and time investment were significant. If you have a large yard and limited experience, hiring a pro is a reasonable choice if your budget allows.

More Outdoor & Landscaping Projects
If you enjoyed this guide, you might find these other DIY projects helpful for improving and maintaining outdoor spaces:

- How to install drip irrigation
- How to build a vine trellis
- How to install landscape lighting
- Beginner’s guide to pressure washing
- How to strip and refinish a wood deck
- How to stain and seal a deck
- How to protect plants from freezing
Note: some product recommendations in the original project were affiliate-linked; purchases may support content creators at no extra cost to you. Always check local codes and consult professionals for required permits or inspections before beginning an irrigation installation.








