Objectales

Popular

How to Install Built-In Laundry Shelves Next to Washer and Dryer

featured 38212

Updating the laundry room? Absolutely. To recap: we replaced the washer and dryer, removed the window shutters and cluttered shelves, frosted the door, patched some ceiling cracks, and painted the room Benjamin Moore’s Sesame—the same color as the kitchen. With those changes in place, here’s how the space looks now:

adding-built-in-shelves-next-to-our-washer-and-dryer

Let me walk you through how we made those shelves. From the start we knew that this narrow 3.5-foot-wide room needed vertical storage to be functional—there wasn’t room for any out-facing cabinets or counters without blocking doors or windows. The washer and dryer take up most of the width, so we decided to add built-ins in the remaining 14.5″ gap to maximize usable space.

img 38212 2

The space is so narrow that the washer and dryer doors wouldn’t open if they were placed on the opposite wall, under the window or fuse box. To illustrate how tight it is, I did my best spider-monkey impression—don’t try this at home.

img 38212 3

Because of the narrow footprint, we focused on going up instead of out. The existing built-in cabinets above the dryer are high, so accessible vertical storage next to the machines was essential. We couldn’t find a ready-made bookshelf that was both narrow enough and deep enough, so we decided to build a custom solution that uses the full depth where possible without blocking the window.

img 38212 4

Our plan split the unit into two depths: the lower portion matches the washer and dryer depth, while the top portion (above the window sill) is shallower to align with the window. This two-tiered approach maximizes storage without obscuring the window or creating an awkward overlap. Below is the sketch I used to determine the cuts and layout.

img 38212 5

I had most of the lumber cut at Home Depot. We used whitewood and a few 1×2″ poplar boards where thinner stock was needed. The vertical divider was made by screwing two 1×12 boards side-by-side for the top and bottom portions, and a 1×10 trimmed with 1x2s for the middle shelf that ties the two halves together. Additional 1x12s became the shelves and more 1x2s served as trim.

img 38212 6

The middle shelf needed to sit flush with the window sill, so I cut and attached 1×2 trim pieces to create a notch that matched the sill. The fit tested perfectly.

img 38212 7

I fastened the bottom of the divider into the plywood underlayment beneath the appliances for stability, and secured it to the middle shelf using a Kreg jig. I initially miscalculated the trim allowance, so the divider overhung the plywood slightly; I fixed that by adding a 1×2 trim along the floor later.

img 38212 8

To support the middle shelf, I added a few cleats on the back and side walls because the divider doesn’t run all the way back. That gap leaves access to the washer and dryer connections and the duct if we ever need it.

We also upgraded the old foil dryer duct to a rigid all-aluminum transition from Lowe’s for safety—it’s a simple swap: remove the old duct, clamp the new one in place with metal clamps and the appropriate wall fitting.

The top divider was installed like the bottom, set back to align with the window so the unit keeps a two-level profile and uses the available depth without overlapping the window.

img 38212 9

For the shelves we chose adjustable, removable shelving so we could reconfigure heights and remove the shelves to access the back of the washer or dryer. I bought four 6-foot metal shelf tracks and shelf clips at Home Depot—the same system we used in our other built-ins—and cut the tracks to length with metal cutters.

img 38212 10

The gap between the divider and wall ended up slightly wider than the 1×12 shelf boards, so I added 1×2 spacers to bridge that space. That ended up making the shelf tracks much more secure than if they had been mounted directly into drywall.

img 38212 11

Painting in place would have been tricky, so I removed the framing pieces and painted them in the sunroom. We applied two coats of Kilz No-VOC primer and two coats of Olympic Premium No-VOC semi-gloss white to the framing. The shelves themselves received two coats of paint without primer and turned out fine—primer on the framing was mainly insurance.

We also painted the right-side wall white to make it feel integrated with the shelving, while leaving the back wall unpainted for a pop of color visible through the shelves.

img 38212 13

After reinstallation, I nailed in the metal tracks, added the shelf clips, and tested the shelves. On the lower half I added a small back lip since those shelves don’t reach the back wall—this prevents items from slipping behind the unit while still allowing removal of the shelves when necessary.

img 38212 14

Here’s the finished built-in. We left a 2″ gap between the appliances and the shelf so the washer can shake during cycles without knocking items off the shelves.

img 38212 16

The adjustable shelves aren’t as visually uniform when empty as fixed shelves would be, but the flexibility is worth it. We can now store both short and tall items without worrying about clearance.

img 38212 17

Storage-wise, we’ve gained a lot of usable space thanks to the full-depth lower shelves and the adjustable layout. For now we’re storing detergent, an iron, clothespins, and other laundry basics. Sherry styled the shelves with baskets and a few decorative items we already owned to keep it tidy and functional.

img 38212 18

img 38212 19

We’re considering using part of this as a drop spot for mail and coupons, so it may evolve into a small home command center.

img 38212 20

Cost-wise, building a custom unit was more expensive than a narrow, shallower off-the-shelf solution, but it lets us use the full width and depth of the nook and offers adjustable customization that off-the-shelf pieces couldn’t match. Budget breakdown:

  • Wood (Home Depot & Lowe’s): $59
  • Metal shelf tracks & clips (Home Depot): $15
  • Primer & paint: already owned
  • Baskets and styling items: already owned
  • TOTAL: $74

We also replaced the dryer transition with an all-aluminum duct for about $10 from Lowe’s.

img 38212 21

If you’re looking for shelving ideas or ways to add vertical storage to a tight laundry space, this approach shows how a custom-built solution can maximize depth and flexibility while maintaining access to appliances and windows.

Current laundry room to-do list:

  • Touch up the brown quarter round with glossy white
  • Repair dinged trim and repaint in semi-gloss white
  • Paint the walls
  • Replace the dryer hose with a safer all-metal one
  • Install adjustable built-in shelving next to the stacked washer and dryer
  • Replace hinges and knobs on the upper cabinetry
  • Install a new light fixture—possibly a small DIY chandelier
  • Add a window treatment—maybe a homemade option
  • Add functional storage near the door for shoes and the dog’s leash
  • Hang art to brighten the room and camouflage the fuse box

We’re already happy with how far the space has come in a few weeks—from cramped and cluttered to organized and purposeful. We still need to figure out where the ironing board will live; we have a plan and will share details after we test it out. In the meantime, tell us what storage solution you love in your laundry room—built-in cabinets, pull-out drawers, a collapsible drying rack, or a dedicated laundry sink? We’d love to hear what’s working for you.

img 38212 22

img 38212 23