Objectales

Popular

How to Install Cement Backer Board for Wall Tile

featured 42819

Demolition can be exhilarating, but there’s always the nagging reminder that what comes down will need to be replaced. We kept that in mind and moved quickly from tearing out the old materials to rebuilding the kitchen.

img 42819 1

We didn’t waste time. Between removing tiles and pulling up plywood, we made a quick run to The Tile Shop in my sister’s borrowed SUV to pick up cement backer board so we’d be ready to install immediately after demo.

img 42819 2

We chose 1/4″ Permabase Ultrabacker cement board, buying four usable 3ft x 5ft sheets after returning the excess from a miscalculation. With a 10% discount offered at the store, our final cost was about $40. We planned to use the cement board along the entire back wall above the stove — our future focal wall where tile will rise to the ceiling around a large range hood and open shelves — and as the standard 18″ backsplash on the other walls.

img 42819 3

I started with the smaller 18″ backsplash pieces because they were easier to measure and cut around the window and outlet openings. For cutting I used a jigsaw and a full-face respirator to avoid breathing in the dust. The cement board was abrasive and chewed up the blade — by the job’s end the blade had significant wear — so a more suitable blade like a diamond-grit one might have been better. Still, the boards cut well enough and we pressed on.

img 42819 5

Setting the cut boards in place was straightforward. The cement board matched the thickness of the old plywood, so the transition was seamless. I leveled each panel and drove the recommended screws until the heads were flush — pokey screw heads will interfere with later tile installation. Sherry kept Clara out of the danger zone while I worked.

img 42819 6

Progress around the room went faster than expected. We’d had a rough time with a similar process when rebuilding a bathroom in our first house, so we were pleasantly surprised this time. The five-foot-tall backer boards fit nearly perfectly on the wall behind the stove, which meant minimal cutting beyond outlet holes. Since Clara was napping, Sherry could help hold the larger panels in place while I drilled, and that teamwork sped things up.

img 42819 7

The dangling outlet near the vent will eventually power the range hood. We placed it in a temporary spot that should work with the final hood location; if needed, the wiring has some slack so we can move it before final installation. The hood won’t be perfectly centered on the tiled section, but it will sit centered on the full back wall once you factor in the doorway and surrounding elements. We plan to balance the composition with floating shelves, houseware displays, plants, and art that will help the wall feel intentional and harmonious.

img 42819 8

We briefly considered tiling to the ceiling on the adjacent wall above the sink and pantry, but decided one focal tiled wall with open shelves and a hood would be enough. Instead, an 18″ backsplash on the opposite walls creates a balanced, rectangular effect without tiling the pantry area, which would have felt odd.

img 42819 9

The kitchen walls aren’t drywall — they’re painted paneling, which adds a soft texture and cozy feel once painted. We ended up buying a new sheet of paneling to match a leftover piece we had and used it to cover the remaining exposed areas to the right of the window where the backsplash will be. It was a small, practical solution that will be painted along with the ceiling and other elements for a unified look.

img 42819 10

A single 4ft x 8ft sheet of paneling was enough to cover what we needed. The store cut the pieces to fit in our car and save us the hassle; I picked up a fresh jigsaw blade there, too, so I could cleanly cut the microwave outlet opening.

img 42819 11

We took one small shortcut: a small upper cabinet will hide an area where we didn’t remove the underlying plywood. That saved time and avoided moving the pantry, and it won’t be visible once the cabinet and crown molding are installed.

img 42819 12

The cement board seams will be taped and covered with thinset before tiling, which is the recommended method to create a secure long-term substrate for tile. When installed, the tiles will hide the seams and create a durable, wipeable surface.

img 42819 13

That off-center window ends up working visually: once the small upper cabinet sits to the right of the pantry and the 12″ floating shelves are added on the focal wall, the window will have equal visual space on each side. The shelving will project out 12″ to hold everyday dishes and décor, keeping items accessible and preventing dust buildup by using things regularly.

By the time we finished this phase, the kitchen already felt more open and balanced. The room still needs paint touch-ups and final finishing — ceiling paint being the least favorite job — but the messy, mismatched stage is behind us. Removing upper cabinets opened up the space and helped us better imagine the tiled backsplash and floating shelves in place.

img 42819 14

Both of the walls in these photos are interior walls; the window looks into an insulated sunroom rather than outside. Because of that, we didn’t add insulation in this step. We lived through last winter with this setup and didn’t notice drafts, so we felt confident proceeding without additional insulation at this stage.

img 42819 15

The demo and reconstruction took two days: one day for demolition and shopping, and one day for installing the new backer board and paneling. It left me pretty sore, but the payoff is worth it. Next up is paint and trim, and then the exciting tile and hood installation that will make the whole design come together.

Have you ever installed cement board or worked with paneling? Any tips for ceiling painting or cutting cement board would be great to hear.

We also recently completed a birthday time capsule for Clara to open on her 18th birthday, and we have a lightly used black over-the-range microwave available if anyone’s interested.