How to Install Crown Molding on Built-In Bookcases
We hoped to have all of the nursery’s extra-chunky crown molding painted, cut, hung, caulked, and touched up by the end of the weekend — and we barely made it. (Also: where does that gross expression “by the skin of our teeth” even come from?)

Crown molding is one of those finishing touches you think will be “nice,” and then you add it and are surprised at how dramatically it transforms a room. Even a plain, boxy space instantly looks taller and more finished. Since many rooms in our house lack dramatic architecture — no soaring ceilings, arches, or built-in columns — the right trim makes a huge difference. Between the little corner built-ins we added and this chunky crown, our 11 x 13.5-foot nursery feels much more intentional and polished.

This is what the room looked like for eight months while we slowly chipped away at it.

We still have work to do — three walls are mostly untouched and the room could definitely use more color, pattern, and personality — but the chunky crown molding alone made the space feel complete and tidy in just a few days.

For the installation we used the same DIY approach we tested in Clara’s room: start with 3 1/4″ baseboard as the bottom layer and run it all the way around the room. We dropped that baseboard about 1.5 inches from the ceiling to create a chunkier profile, used a spacer and a level to keep everything straight, and marked studs with painter’s tape so we could nail into solid backing.

The second layer was the crown molding itself — a beefy 4 5/8″ profile — installed over the baseboard for that substantial look. On one side you can see the finished “crowned” assembly; on the other side there’s baseboard waiting for the crown to complete the effect. We matched this profile to the first-floor crown and our master bedroom so everything reads as a cohesive whole.

To save time we used pre-primed baseboard and crown and painted the pieces on the floor on a drop cloth before hanging them. This method is faster than painting in place and leaves only minor touch-ups after caulking. We even painted a small portion in the built-in color for continuity, while the rest stayed white — and the result feels intentional and clean.

Here’s the crown between the built-ins right after hanging and before caulking or touch-ups. The ceiling has tiny undulations that look uneven until you run a bead of caulk along the seam and smooth it, forcing the filler into those small gaps. We apply caulk in manageable sections — about a foot at a time — and wipe it off quickly so it stays only in the cracks and rarely needs repainting on the ceiling or molding.

After filling nail holes, final paint touch-ups, and removing the stud-marking tape, the trim looks much more refined. It’s amazing what a little caulk and paint can do.

If you want details and photos of this baseboard-plus-crown technique from another room we did, search for our Clara’s room crown molding project. The cost for a larger room ran about $137; this nursery’s crown materials were around $115, plus caulk and paint if you don’t already have them.
On the bedding front, I finally started on crib textiles. I found an organic crib sheet on sale for under $10 — a pleasant change from what we paid a few years ago — and used 1.5 yards of green fabric from a craft store to make a custom crib skirt for roughly $3.73. Small victories at the checkout led to a very happy “Mom Victory Dance.”

To make the crib skirt I cut three panels — two sides and a front — using the crib skirt area’s measured height and width and adding 3″ to each dimension for 1.5″ hems. For patterned fabric, be sure each panel’s pattern runs in the same direction so the final skirt looks intentional. Depending on the print, you may need extra yardage.

I debated sewing versus using hem tape. Since the hem tape held up well for Clara’s crib skirt, I used it again. You’ll need fabric, hem tape, scissors, an iron, and some Velcro tabs. Hem tape makes neat hems quickly: iron the tape on, peel the backing, fold and press, and you have a clean finish. To join panels, place a strip of hem tape along the back edge of one panel, overlap the next panel, and press to fuse. The seam ends up on a crib corner where it won’t be visible.

I attached the skirt to the metal crib frame with small Velcro tabs so it’s removable and washable. Hem tape is also washable if you follow care instructions and avoid high heat.

We plan to lower the mattress as the baby becomes more mobile, so the skirt won’t always be necessary to hide the gap between the mattress and the drawer — but it’s a charming detail, especially for under four dollars.

We darkened the crib’s bottom drawer with two coats of satin gel stain to balance its tone with the floors and dresser tops. A darker base helps ground the light crib and ties in with the built-ins’ hardware and the room’s other accents. We sealed the stain with two satin coats of a low-emission acrylic sealer to reduce off-gassing and keep finishes safer for a nursery environment.

I quickly staged the built-in shelves with a few items so they weren’t glaringly empty, but I’m excited to collect baskets, frames, books, toys, and other decorative objects to add color and personality. The built-ins will be practical storage and a big part of the room’s visual identity.

Above the crib we’re weighing several options: a large-scale piece of art, a slatted accent wall, or a dramatic mobile. We tried leaning bicycle prints above the crib, but they felt too busy next to the built-ins and seem to work better on the opposite wall. Right now we’re leaning toward a bold, oversized mobile with pops of green, black, and white, and perhaps an animal motif that nods to the nursery’s playful theme.

What did you work on this weekend? Do you have bookcases ready to style or blank walls begging for attention? Tell us what projects are getting you excited.
Psst — If you want to follow along with the nursery’s progress from the very start, search for our planning and rug post, the dresser-sourcing post, the wall and ceiling painting post, and the two-part built-in project posts to see how this space came together step by step.








