Objectales

Popular

How to Install Kitchen Crown Molding

featured 44739

We’ve long joked about our kitchen photos with a little disclaimer—“oh, and we still need to add crown molding.” That unfinished edge where the wall and tile met the ceiling is finally gone. After a few weekends of measuring, cutting, coping, caulking and painting, the crown is installed and it makes a big visual difference.

img 44739 1

Before I explain how we finished it, a quick fix we had to do first: I had sealed the hood vents in a hurry with regular duct tape. Turns out duct tape is not the right choice for ductwork—metal foil tape is. After a few helpful comments from readers, I removed the old tape and wrapped the ducts properly with foil tape so we won’t have ventilation problems down the road.

img 44739 5

Now back to the crown molding. Our kitchen turned out to have three different types of molding: a traditional crown around most of the perimeter, a slightly smaller version on the fireplace side, and thin cove molding along the beams—except for one beam that surprisingly had a much thicker crown on one side. Because the cabinets used to go to the ceiling on that side (we took those cabinets down in November), we’d been living with several crown-less gaps that left the room looking unfinished and shadowed.

img 44739 7

The tricky part: none of the profiles matched standard store stock exactly, so replacing pieces with new trim from the store wasn’t a straightforward option. Fortunately, I had saved the trim that came down with the cabinets, which gave me most of what I needed. After priming those reclaimed pieces with a stain-blocking primer (we like Zinsser Smart Prime for wood trim) and finishing with a couple coats of the same crisp white Behr paint we used on the rest of the trim, the reused pieces blended in nicely with the kitchen.

img 44739 8

I did come up short on a few longer sections of the larger crown. The solution was to repurpose the thick crown from that one mismatched beam and replace it with a smaller cove molding sourced from the store. That swap made the whole room read more consistently and saved us from redoing trim on every beam and perimeter edge. In a way, the mismatched beam ended up being the key to finishing the job without starting from scratch.

img 44739 10

Cutting crown molding was a learning curve. You cut it at the angle it sits against the ceiling, which is counterintuitive because it’s not flat on the saw table. Some tutorials suggest attaching a guide block to the saw table to hold the molding at the correct angle; that didn’t work well for me with the supplies I had and the cold weather, so I ended up holding pieces in place by hand while making cuts. After cutting compound miters, I used a coping saw to remove the excess so corners would sit flush. Marking the cut lines with a darker marker, as many guides recommend, helped me stay accurate.

img 44739 12

Because this was my first time, some cuts weren’t perfect and the ceiling isn’t perfectly flat—typical of older homes. A little caulk and paint fixed most imperfections. We used white paintable DAP caulk, ran thin beads where needed, smoothed them with a finger, let them dry and then painted over them. That simple finish work made the differences disappear and gave the trim a clean, finished appearance.

img 44739 21

One unexpected stroke of luck: I found a single matching piece of the slightly smaller crown in a basement trash bucket, which allowed me to patch a small gap without replacing all the trim on that side of the room. And when the store-bought cove molding didn’t match the existing non-standard size exactly, replacing just one side of the beam proved far less invasive than redoing multiple beams and perimeter lengths.

img 44739 19

After all the cutting, nailing, caulking and painting, the room looks much more finished. It’s a subtle change but makes a noticeable difference—especially around the pantry and the hood where that dark, unfinished line used to be. We still have a few tasks left—hanging a pendant over the sink, finishing decorative trim on the peninsula, installing the dishwasher and eventually putting in cork floors—but adding crown molding was an important step toward a polished kitchen.

img 44739 22

With the shelves emptied to accommodate the trim work, we took the chance to refresh styling on the open shelves. We rehung a few frames with removable picture hanging strips so we didn’t have to drill into tile, added a couple more frames and simplified some items we weren’t using as much. The window now has a bit more breathing room on each side, and once a pendant is installed it’ll feel even more balanced and complete.

img 44739 26

If you’re planning your own crown molding or kitchen trim project, expect a mix of measuring, test-fitting, coping and touch-up work. Read a few tutorials first, practice on scrap pieces, and don’t skip the primer and caulk—those finishing steps make all the difference. What did you tackle this weekend—trim work, shelf styling or a small DIY ventilation fix?

img 44739 30