How to Remove Kitchen Cabinets for Renovation
We realized early in our appliance search that we needed an unusually small refrigerator to fit the existing built-in space in our kitchen. After plenty of searching, we accepted that finding a perfectly sized stainless, side-by-side fridge like we loved in our first kitchen was unlikely. So we started leaning toward a different approach: removing the built-in cabinet box around the fridge to give ourselves more flexibility with dimensions. That would let us shorten the hollow top of the upper cabinet, rehang it higher to accommodate a taller fridge, and rebuild the sides at a new depth so the new appliance would sit more flush and custom-looking.


Even if we had somehow found a tiny fridge to slide into the existing cavity, we’d still have to rebuild the side panel for a cleaner finish. The old fridge stuck out about six inches past the side panel, exposing top hinges and making the beam beside the cabinet look awkward. We figured this project would probably require a little “beam surgery,” but we were ready to adapt our plan as we went—standard practice around here.

The official start of our kitchen demo was removing the side panel and the cabinet above the fridge, though we planned to reuse and adapt many of the existing cabinets rather than gut the entire kitchen. Step one was simple: empty everything from the cabinets. We also cleared the neighboring cabinet just in case it needed to come down. Our little helper contributed when the project involved arranging toy pigs on the step stool, but otherwise she preferred snuggling with her stuffed giraffe while we worked.

With the cabinets emptied, we rolled the fridge out of its cubby to see what was behind it. That revealed a mysterious electrical cord and confirmed the cabinet was attached at the sides and top—but not the back. We also discovered that the beam beside the cabinet actually ran all the way through it. That was an important detail for planning how we’d alter the cabinets and how far we wanted the cabinetry to extend.

We also found the order form tucked behind the cabinet dating to November 1982, which told us the cabinets were custom-made by QuakerMaid. That explained why the construction felt solid and why the cabinet sizes were so standard and useful even after decades of use. It was a fun kitchen artifact to uncover.

Detaching the fridge cabinet from the one beside it was straightforward at first: we found long screws running through the tall cabinet into the fridge unit and removed them. But the assembly didn’t come down easily. It turned out a floor-to-ceiling side panel on the left was holding everything up. The panel was flush and had no visible fasteners, so after trying gentle removal unsuccessfully, we made a clean decision to cut through it with a jigsaw. That allowed us to preserve as much of the panel as possible in case matching wood would be useful later.

Before we cut, we reinserted three long screws through the cabinet on the right to temporarily support everything. That held things steady while we each made a careful cut with the jigsaw. The panel swung free and then we removed the support screws—one of us braced the cabinet below during the final removal to be safe. Remarkably, our child slept through all of the drilling and sawing.

Removing the cabinet confirmed the beam ran completely through the space. That helped settle a design decision: we would not extend the altered cabinets all the way to the ceiling. We love the look and storage of ceiling-height cabinets, but cutting the beam again felt wrong given how it intersects the cabinet and how it conceals a damaged seam in the ceiling from previous home additions. Also, other built-ins in the room—like the pantry—aren’t ceiling-height, and we want visual balance across the space.

Our plan now is to repaint and refinish the altered cabinets, add trim across the top for a polished look, and rebuild side panels at the new depth so the fridge appears integrated. We’re aiming for a cohesive appearance that harmonizes with the other built-ins, rather than forcing ceiling-height cabinetry around the beam. For inspiration we kept a mental note of kitchen photos that show a neat trim finish at the cabinet tops, which is the look we want to emulate once everything is painted.


At the moment the space shows a mystery wire, some unpainted surfaces, and—best of all—room for a taller refrigerator. But as we opened up the area we started to wonder if we could improve the fridge’s placement even more. Moving the appliance to a less cramped corner would require more drilling, lifting, and general labor than we had energy for that day, so we decided to pause and consider the options. Once we finalize the plan and complete the work, we’ll share more photos and details of the demo, cabinet rebuild, and final trim work.

Pssst—We also saw a really clever nightstand-to-play-kitchen conversion featured on BabyCenter that inspired some playful storage ideas for our own project.








