How to Seal Gaps Between Your Stove and Cabinets
Some parts of a kitchen remodel aren’t as thrilling as opening up a wall or picking a backsplash, but they still matter — especially when you want the countertop templater to get precise measurements. We tackled a few small but necessary jobs before the counter guy arrived: filling gaps around the stove, squaring off the peninsula for templating, and doing some quick paint touch-ups to make the space feel less unfinished.
First on the list was closing the gaps beside our range.

The base cabinet we removed was 36″ wide, while our stove is about 30″, which left roughly 2 3/4″ of empty space on each side. Narrow pull-out drawers tend to be at least 3″ wide and none matched our existing cabinet doors, so we opted for simple filler strips. We also wanted the stove centered under the hood — moving it over would have required widening the ceiling hole for the hood and created more work. In the end, two slim, plain filler pieces would let our penny-tile backsplash and floating shelves remain the visual focus.

I picked up a few pine project boards at Lowe’s, cut them to size, drilled pilot holes with a Kreg jig, and screwed them into place for a solid fit.

We installed filler pieces at the front for the visual gap and added a back filler to give the counter installer something to support against. That kept the edges stable for templating and future countertop attachment.

Each side ended up with three filler layers. Two might have been enough structurally, but the boards were inexpensive — the whole project cost about $11, which was far cheaper than specialty pull-outs.

Here are both sides finished and ready for the range to be slid back into place:

Not bad — once the countertops are installed and the cabinets are primed and painted, these gaps will blend right in. Several existing base cabinets already have similar 2.5″ fillers, so this will match the rest of the kitchen.

On closer inspection we noticed a small remaining gap of just over 1/4″. To tighten things up we added a 3/8″ project board strip that fit perfectly into that space. A couple more dollars (about $4) later, the total project cost rose to roughly $15 — still a bargain.


I nailed the thin strips in place, keeping them flush with the front fillers for a neat, even appearance.

Here’s the view with the extra slivers installed on both sides. They’re strictly cosmetic, so I didn’t extend them beyond the front filler panels.

Sliding the range back in made a big difference. It’s snug enough to look finished but still removable when needed. Once we demo the tile behind the stove it will sit even closer to the wall, and the future toe kick across the base will create a seamless bottom line.

With the stove gaps solved, the next small task was on the peninsula: we needed a flat back panel so the templater wouldn’t interpret any angled corner.


I started by attaching a small corner brace — two scrap boards joined at 90 degrees — to anchor the plywood panel against the half wall so the panel’s edge would sit flush with the cabinet backs.

I had bought a thin utility plywood panel earlier when I picked up plywood for our refrigerator built-in, which made transport easy. The Lowe’s cutting crew trimmed it for me, and I cut off a 3″ overhang with a jigsaw when our end cabinet size changed from 21″ to 18″. The panel only cost about $9.

After trimming it to fit, I nailed the panel in place. It’s plain for now but accomplishes the immediate goal: a straight, square back for the peninsula so the templater won’t assume any unusual angles. We’re planning trim details later — baseboard, corner trim, maybe board-and-batten — and it will be painted to match the cabinets.

This panel will support a 12″ Corian overhang on two sides to accommodate four stools. We’re considering lighter, acrylic-style stools for an airy look.


While not required for templating, we also tackled several paint touch-ups. Painting trim, drywall edges, and leftover paneling from the pantry/fridge shuffle and wall opening made the space feel more cohesive and livable — and since we had the paint on hand, it was an easy sanity-saving step.

We painted the inside edge of the half-wall a soft gray to match the dining room; it reads almost white against the door jamb and ties the two spaces together. The temporary threshold visible in one photo is just a piece of leftover paneling flipped over and nailed down to bridge the gap created when the wall was removed. Later it will be covered with cork and a small threshold will join the new flooring to the original hardwood.







A few readers asked for a living-room vantage point, so here’s a view from the back of the house. We love seeing the big picture window from this angle. Widening this doorway is appealing but it’s a major structural job — this used to be an exterior wall — so it’s on the “maybe someday” list. For now, the partial separation gives the living room a bit more privacy while still opening the sightlines.

All told, this was a post about small but meaningful progress: filling the gaps around the stove, attaching a straight panel to the peninsula, and doing paint touch-ups. Thirty photos later, it feels a little more done — and we still grin every time we walk into the kitchen.
What small updates have you made around your house lately? Any last-minute projects you’re trying to finish before the weekend or a holiday?
Psst — we announced this week’s giveaway winner. Clickhere to see if it’s you.








