Install a Pull-Out Trash Can in a Kitchen Cabinet
Thanks for all the helpful ideas and suggestions on the pantry project we started the other day. We had so many directions to choose from, but first things first: we emptied the pantry completely and even took the door off its hinges so we could prime and paint the interior without obstacles.

One change we decided on after that planning conversation was to remove the trash can from the pantry and install it in a nearby cabinet instead. The cabinet sits at the end of our peninsula, facing the prep area rather than the eating area. Please ignore the pantry cast-offs on the counter in these photos—we were mid-project.

We hadn’t experienced odor problems with the trash in the pantry after a month of use, but moving the garbage made sense for a few practical reasons:
- That bottom shelf space could be put to better use if it weren’t taken up by a bulky trash can and the clearance needed for its lid.
- The foot-operated can in the pantry wasn’t truly hands-free anymore—opening the pantry door, then stepping in to kick the can felt inefficient compared with a single, more accessible motion.
- The cabinet we chose was mostly unused, holding only a few vases. It was a missed opportunity for better organization.
Instead of cramming a free-standing bin into the cabinet, we picked up a recommended solution: a Rev-A-Shelf pull-out container system. There’s also a larger version with two cans, but our cabinet wouldn’t easily fit that configuration. We also figured a smaller single can would encourage more frequent emptying. We have a plan brewing for recyclables, but it still needs some polishing.

The cabinet wasn’t a perfect match from the start because of a shallow built-in half-shelf across our lower cabinets that prevented the can from sitting all the way back. It’s nailed in place on every side, so it isn’t removable or adjustable. That meant I’d need to do a little woodworking.

Following the product instructions, I positioned the paper template on the shelf, drilled pilot holes, and screwed the two metal tracks into the cabinet floor. Snapping the rest of the pieces into place was quick—without the half-shelf issue the whole conversion would have taken about ten minutes. Still, with the track installed I could mark the shelf where I needed to cut (the green tape shows my guide).


I only needed to notch out a small section—about 3 inches deep by 8 inches wide—to allow the can to sit fully back in the cabinet. I used a compact plunge saw designed for small cuts because it’s easy to control in tight spaces. The cut was fast but messy; sawdust went everywhere (as you can see in the photo). Lesson learned: cover more surfaces next time.

After cleaning up the dust, the trash can slid into place and everything looked good. Still, I wanted to make the cabinet feel even more like a modern built-in, so I added a door mounting kit sold by the same manufacturer to attach the cabinet door directly to the pull-out unit.


Installing the door kit was a little trickier—the instructions were vague in spots. The concept is simple: you attach two small bracket “fins” to the sliding tray, then bolt on larger brackets that hold the cabinet door. In practice, working with tiny nuts and screws in cramped spaces was fiddly and required patience.


Once the fins were attached, I added the larger brackets where the door would mount. When I tested the setup without the door attached I realized our older door design caused a fit problem: the doors on these cabinets are partially recessed into the frame and sit on a lip, so the brackets initially overhung the frame and the door wouldn’t sit flush.

I improvised by reversing the orientation of the brackets so they faced inward instead of outward. That adjustment brought the door flush with the adjacent cabinetry. To align the door perfectly before final fastening, I used the included double-stick tape as a temporary anchor—press the door where it looks right, peel it away while it stays stuck, then secure the connection from the back with screws. Just be careful to only drive screws into the thick cabinet frame so they don’t poke out the other side.



After a bit of back-and-forth disassembling and reassembling, everything came together nicely. The finished cabinet looks cleaner and functions much better than before. It even gives our older cabinets a slightly updated feel, and the pull-out system is portable enough to reuse later—whether in a future kitchen or even in a garage workshop.

My only remaining task is to touch up the screw holes where the old hinges used to sit on the right side of the cabinet. I’m toying with the idea of installing faux or “dummy” hinges for symmetry, but that’s a small project for another day.


We also bought baskets, bins, and other pantry organizers on the same trip, so once priming and painting are finished we’re excited to restock the pantry in a much more organized way. With snow keeping us inside for the next few days, we’ll have plenty of time to tinker and get the pantry party started.
P.S. If you want to read more home improvement updates, check out the home improvement category on our site for a variety of projects and tips.
*This post contains affiliate links*








