Objectales

Popular

Marble Herringbone Backsplash: How to Install It Like a Pro

featured 65492

Marble Herringbone Backsplash Transforms Our Laundry Room

“It’s like a cable knit sweater on the wall!” That’s how I described the marble herringbone backsplash after we installed it behind the washer and dryer. The small marble mosaic sheets add texture and warmth to the room, and the result feels far more finished than the blank box we started with. We used thirteen sheets of tile to cover the back wall and it made a big visual difference.

LaundryTileAfterShot

Ignore the unfinished shelf for now — it still needs to be stained, sealed, and installed — but the shelf will rest on removable L-brackets so we’ll retain easy access behind the machines. That means no more random socks slipping into the gap, plus the wood will bring a bit of organic contrast to the cool, polished marble.

img 65492 2

We built the shelf first so we could mark the exact height to tile to, and to avoid tiling where the brackets would attach. That made hanging the brackets after tiling easier and kept the finish cleaner.

img 65492 3

On our mood board the wood stain tone we’re aiming for is nearer to sample #1, and the wall tile is the Hampton Carrera marble (the look we wanted was bright, slightly warm veining on polished white marble). We tested a few stain and sealer combinations on scraps to decide the final finish for the shelf and counter.

img 65492 4

This installation had two new elements for us: mosaic marble sheets in a tight herringbone pattern, and a premixed mastic adhesive so we could tile directly over painted drywall after scuffing it slightly. The mastic we used from The Tile Shop has the texture of spackle and was applied similarly to thinset, but we used a smaller 3/16″ v-notch trowel for better coverage with the mosaics.

img 65492 5

Cutting the mosaic sheets was one of our worries because the tile was on backorder and we wanted to avoid breakage. For previous projects we’d used tile nippers successfully, but we read that a wet saw can work well with marble mosaics. With a steady feed, lots of water on the blade, and two scrap pieces under the sheet so it had a flat surface across the blade, the wet saw made clean cuts and preserved the mesh backing.

img 65492 6

We mostly needed to trim the tops of tiles for a flush fit against side walls and cabinet undersides. The new saw’s rolling tray and laser guide helped keep cuts straight along the angled tiles, and the results were excellent.

img 65492 8

When it was time to set the sheets, I spread the mastic with the flat side of the trowel, then combed it with the v-notched side to create even ridges. Because mastic sets faster than thinset, we worked in small sections — usually two sheets at a time — so the tiles could be positioned and nudged before the adhesive began to skin over.

img 65492 11

Sherry handled laying each mesh-backed sheet and nesting the pattern so seams between sheets were as invisible as possible. Some mosaic sheets had slight spacing variations, so we aligned and sometimes shifted sheets to match the herringbone flow. Where mesh backing interfered with an edge, we carefully trimmed it away so adjacent tiles could sit tightly.

img 65492 12

To disguise horizontal seams across the wall, we staggered the sheets vertically. For example, a vertical run above the appliances might use a full sheet on top and a half sheet below, while the next run starts with the leftover half sheet on top and a full sheet beneath. That stagger breaks up any continuous seam lines and makes the pattern read as one cohesive field.

img 65492 14

We installed the sheets in about two hours while our toddler napped. Because the mastic cures faster than thinset, we let it dry overnight and grouted the next morning. The gaps between the herringbone tiles are wider than an eighth of an inch, so we used sanded grout in Standard White (also from The Tile Shop) to fill them.

img 65492 17

Grouting this wall required more material than the floor because of the many angled gaps. I mixed a single bucket and worked in manageable sections so the grout wouldn’t dry out before being tooled and wiped. I also set a scrap board where the shelf will sit to protect the floor from drips.

img 65492 19

After wiping excess grout with a damp sponge, a haze developed as the grout dried. Polished marble is sensitive, so chemical haze removers aren’t recommended. Instead, I buffed the haze away with a microfiber cloth and a little elbow grease. It took a couple of passes to get the marble gleaming, and we may do one more final polish after the shelf is installed.

img 65492 22

img 65492 23

Update: If we ever replace the washer and dryer, the standard width should allow a new set to fit in the opening. The height might vary, so we can remake the removable shelf if needed. We kept extra tile and grout on hand for future adjustments.

img 65492 25

We’ll return with a follow-up post showing the finished stained and sealed shelf and counter, plus details on reinstalling the washer and dryer and hooking up the overflow drain. For now, here’s an updated to-do list showing completed and remaining tasks:

  • Move washer & dryer and remove cabinetry (see prior progress updates)
  • Demo cased opening, side wall, back wall, part of the floor and the attic step
  • Frame new walls & doorways
  • Move laundry plumbing hook-ups & drains
  • Move laundry electrical plus other outlets/lights
  • Move dryer vent & HVAC duct
  • Hang drywall
  • Add insulation
  • Mud, tape, and sand all the drywall seams in the new room
  • Prime & paint laundry room and hallway walls
  • Tile & grout new laundry floor
  • Hang upper cabinets and install lower cabinet
  • Reinstall washer & dryer
  • Stain, seal, and install the wood counter & shelf
  • Rehang the laundry door & add the new glass door to the future bunk-room
  • Add cabinet fillers, crown molding, baseboard, & door casings
  • Install cabinet hardware & soft-close drawer upgrades
  • Add a ceiling light fixture & under-cabinet lighting
  • Hang art, ironing board, and bring in other laundry room items (drying rack, trash can, etc.)
  • Finish touches and repairs (fix drywall in the garage, add the attic step, etc.)

We’ve still got seven items left to tick off, but having a functional washer and dryer again makes this feel like the home stretch. Also, there’s a good chance Sherry is currently admiring the tile — I wouldn’t be surprised if she’s still petting it.