Prevent Frozen Pipes This Winter: 5 Practical Tips
We assumed frozen pipes weren’t a concern after moving to Florida, but an unexpected arctic blast plunged nighttime temperatures into the low 20s for three nights (with a record low of 18°F in our area). Florida homes aren’t always built for sustained subfreezing weather, and frozen water expands as it freezes—causing pipes to crack or burst and leading to leaks or flooding.

Fortunately, with a few practical steps we kept our pipes from freezing, though many neighbors were not so lucky. Several people we know experienced burst pipes, so we’re grateful the measures we took protected our home. Below are five effective precautions that worked for us, plus a plumber’s tip that saved our outdoor shower.
Tip 1: Identify Your Vulnerable Pipes
Start by surveying your plumbing to pinpoint locations most likely to freeze. This helps prioritize actions and ongoing checks during cold spells. Common vulnerable spots include:
- Outdoor fixtures like hose bibs and outdoor showers
- Pipes in unconditioned spaces such as garages, attics, and crawl spaces
- Pipes along exterior walls
- Pipes tucked inside cabinets or closets away from heat sources
- Pipes exposed to wind, such as those on docks
- Any uninsulated runs of pipe

Our main concern was exterior plumbing: the water heater, the outdoor shower, and hose bibs. Interior plumbing was lower risk because we had whole-house power and heat via a generator, but if your heat could go out, interior pipes can freeze too. If you anticipate losing heat, prioritize insulating interior pipes in attics or garages and follow the drip and shutoff tips below.
Tip 2: Insulate Exposed Pipes
Insulation was the quickest, most affordable upgrade we made. We bought self-sealing foam tubular pipe insulation and installed it on exposed outdoor copper and PVC runs. These tubes are inexpensive and simple to cut and fit around straight sections; pick up elbows and tees or use adhesive insulating tape where a full tube won’t fit.

It took about 15 minutes to cover uninsulated outdoor pipes. For tight or oddly shaped spots we applied adhesive insulating tape, which works well around hose bibs and areas mounted close to siding.

We also checked attic plumbing and pushed blown insulation back over any exposed pipes. Even indoor plumbing can freeze if it runs through cold attics, garages, or crawlspaces, so cover any exposed sections you find.
Tip 3: Keep Water Moving — Let Faucets Drip
Moving water resists freezing, so letting faucets drip slightly prevents pipes from freezing solid. Drip both hot and cold lines where possible — not just cold — because hot-water lines can freeze too if left stagnant. We left interior bathroom and kitchen faucets on a slight trickle and monitored them.

Our outdoor shower posed a challenge: running it fully for days wasn’t practical. A local plumber advised removing the showerhead and hand-tightening a cap in its place so a small, steady drip remained. Then set the mixer to a mid-temperature so both hot and cold lines saw flow without creating a full spray. That simple adjustment kept the outdoor lines from freezing without wasting excessive water.

We kept interior and exterior fixtures lightly dripping for the entire cold snap, checked them for ice or blockages, and posted reminders so family members wouldn’t accidentally turn them off. The water cost is minimal compared to the damage and cleanup from a burst pipe.
Tip 4: Shut Off and Drain When Away
If you’ll be away or want a different approach, shut off the water to parts of the home or to the whole house. After shutting off the supply, release system pressure by opening the lowest faucet or hose bib until flow slows. That drains standing water and reduces the risk of freezing and bursting in vacant pipes. This is also a good practice whenever you travel to avoid summer leaks and winter freezes alike.
Tip 5: Pools and Freeze Protection
We worried about exposed pool plumbing, but our pool controller includes a Freeze Protect feature that cycles pumps and returns water whenever air temperatures fall below a set threshold. That continuous flow and occasional cycling prevents pool water from stagnating and helps avoid frozen equipment. Older systems can often be set manually to cycle pumps during cold spells. Check your pool controller or consult your service company to confirm how your specific system handles freezing temperatures.


We watched the pool’s fountains and spa cycles during the cold snap and felt reassured that the system was protecting the plumbing. Ensuring a reliable power source, such as a backup generator, also increases the chance that freeze-protection features will keep working during an extended event.
Nothing Is Foolproof
No single approach guarantees zero problems in every situation, especially during an extreme weather event. However, the combination of identifying vulnerable pipes, insulating exposed runs, keeping water moving, shutting off and draining when appropriate, and confirming pool freeze protection significantly reduced our risk and gave us peace of mind.
Additional Cold-Weather Preparations
Alongside pipe protection, we also took steps to protect outdoor plants during the freeze, using covers and other strategies to reduce damage. If your heat could fail, review plans for preventing frozen interior pipes and consider temporarily shutting off or draining lines you can’t monitor. A little preparation goes a long way toward avoiding costly repairs and disruption.

*This post contains affiliate links, so we may earn a small commission when you make a purchase through links on our site at no additional cost to you.








