Spray Paint Hardware: Prep, Paint, Protect
How do you like those handles?
(Yes, handles and apples. Same debate. And no, celebrity cameos aside, this is just a DIY story.)
I’m back with the hardware makeover step-by-step and a bunch of photos we couldn’t fit into our door-painting post earlier this week. We replaced and refinished the hardware on our living room sliding doors and front door, and it was such an easy upgrade that I wanted to share the process in detail.

The original sliding door handle was, frankly, a mess—rusted, worn, and dated. Up close it didn’t look like shiny new brass at all; it was corroded and neglected.

We took all of that hardware off in about five minutes. One person handled each door and we removed screws from the front, back, and side with a standard Phillips screwdriver. The front-door doorknob and the rusty door knocker came off the same way.

If you want more on the painting prep we did around the hardware, see our door-painting post for the sanding and priming details. For this article, here’s the pile of hardware we removed: sliding-door handles, a doorknob, a deadbolt, and a door knocker—basically a Gold Hardware retrospective.


After researching and talking with paint experts, we followed a commonly recommended approach for refinishing metal hardware for a durable, long-lasting finish:
- Roughen the surface slightly with high-grit sandpaper (200+ grit) or use steel wool for light abrasion.
- Use a liquid deglosser to remove oils and sanding dust so the finish will adhere properly.
- Apply a thin, even coat of primer made for metal surfaces.
- Apply two to three thin, even coats of spray paint formulated for metal in your chosen finish—in our case, oil-rubbed bronze (ORB).

I started with sanding and quickly learned a lesson: sanding can leave visible scratches in some finishes that thin spray coats might not fully hide. I recommend testing on a small, hidden area first. Some readers suggested steel wool or very high-grit automotive sandpaper for a gentler, more consistent texture—good advice to try next time.
After giving up on aggressive sanding, I moved to the deglosser. Wearing gloves, I wiped the hardware thoroughly and let it dry until it wasn’t wet to the touch. When I picked up the paint can, I noticed the paint I chose already included primer, so I skipped a separate primer step and applied the paint-primer product directly.

Key tips for spraying hardware:
- Position parts upright through cardboard so you can reach every angle without touching the wet paint.
- Insert a spare key halfway into a lock to protect the interior of the keyway from overspray while leaving the surrounding metal accessible.
- Put screws partially into their holes so you can spray them and have them match the finish.
- Spray three thin coats about 15–20 minutes apart—thin, even layers prevent drips and give better adhesion.



After three coats and a bit of drying time between each, the results looked great—rich, dark, metallic, and much more in line with the updated look we wanted.

I let everything cure for about six hours before reinstalling. That extra curing time reduced the risk of scuffs during reinstallation. Reinstalling was straightforward and everything functioned as before; in the first two days of use there were no signs of flaking or damage.

We’ll keep an eye on long-term durability—these doors get heavy daily use (especially with a dog who loves going in and out)—and report back. But so far, the painted hardware is holding up and gives the room a much-improved look without the cost of buying all new pieces.
The oil-rubbed bronze finish can appear almost black in photos, but in person it’s a warm, metallic chocolate tone that pairs wonderfully with dark curtain rods and exposed beams. It transformed the white doors into a statement detail that suits the room perfectly.




We also refinished the front-door hardware and are very happy with how cohesive the changes look throughout the entryway.


In short, our process was:
- Use a liquid deglosser (or very fine steel wool) to prepare the surface.
- Lay parts upright on cardboard so all sides are accessible.
- Block keyways with a half-inserted key to prevent overspray inside locks.
- Apply three thin, even coats of a paint-and-primer spray for metal, waiting about 20 minutes between coats.
- Allow a full cure (we waited about six hours) before reinstalling.
The total cost for our paint job was minimal—about the price of one can of spray paint—compared to replacing knobs and locks, which could run several hundred dollars. If the finish proves durable over time, this is an affordable way to update hardware and unify a room’s style without a big investment.
Update: Our handles are still holding steady—check our follow-up post for long-term results.

*This post originally referenced products we used and recommend based on our experience.*








