8 Prep Steps to Take Before You Start Tiling
We’re nearing the finish line on both duplex kitchens, and one big milestone is finally checked off: installing the backsplashes. Because this is a two-unit house we tiled two kitchens at once, which felt intimidating at first, but we knocked both backsplash installations out over a long weekend. Today I’ll share the results and eight practical tips to help you plan a faster, cleaner tile project.

A few small finishing touches remain—floating shelves, and a wipeable beadboard-like treatment for the stove wall—but Sherry staged a few accessories to make the spaces feel more finished. It helps morale and gives a clearer sense of the final vision.
Below is a quick before-and-after: this is the room after cabinet installation but before the backsplash:

And here’s the space now, after the tile went up:

Covering the walls with tile from counter to ceiling created the dramatic color and pattern impact we wanted for each kitchen. The bold tile shows up from the front door and lifts the whole downstairs—it’s a major mood boost for both units.

Both tile styles are porcelain from Tile Bar: the pink pattern paired with blue Ikea Kallarp cabinets is Bella Tate, and the blue pattern paired with wood Ikea Askersund cabinets is Bella Moma. We grouted both with Mapei Flexcolor in Warm Gray—the grout we reach for for many projects because it’s flexible, durable, and easy to work with.

Both tiles are durable porcelain that mimic cement tile aesthetics without the extra maintenance and staining risk of real cement. Each tile is roughly 9 x 9 inches and priced at about $7.99 per square foot, so the tile for each kitchen ran just under $400. It’s not the cheapest option, but for two full-height statement backsplashes it feels like a great value.

We tiled, grouted, and photographed both backsplashes in about 2.5 days. The biggest lesson from the job is this: prep and planning are essential. It may not be the most exciting part, but taking the time to measure, lay out, and plan pattern placement will save time, headaches, and improve the finished look.
8 Things To Do Before You Start Tiling
Most of these tips apply especially well to medium-to-large tiles and patterned tiles. Smaller mosaic tiles hide small mistakes more easily, but large tiles can show tiny slivers or uneven edges that make the entire pattern look off. Here are the steps we recommend before you spread any adhesive.
1. Find Your Maximum and Minimum Measurements
Measure the tiling area precisely—down to 1/8th or even 1/16th of an inch if possible. Walls and ceilings often slope, so measure multiple points to identify the highest and lowest spots. For example, the chimney side of one kitchen was half an inch shorter than the opposite corner. Knowing those extremes helps you plan how tiles will stack from top to bottom.

Check for bows by holding a long level against the wall across several points. Small bows can usually be addressed with grout or caulk; bigger ones may require a layout adjustment so you don’t end up with awkward slivers of tile.

2. Lay Out and Measure Your Tile
Don’t rely on box dimensions alone. Lay out a row of tiles with spacers on the floor to get accurate measurements and to see how the pattern flows. In our case, the tiles measured closer to 8.75 inches rather than a full 9 inches, and that small difference changed the layout math. Laying them out showed we would be short by nearly an inch if we used seven full tiles, which would have forced an awkward 1-inch sliver at one end.

Instead, we adjusted to use six full tiles and two slightly larger half-tiles top and bottom. That centered the pattern vertically and disguised the ceiling slope, so each end reads as roughly half a tile instead of a glaring mismatched sliver.

3. Plan for Outlets and Obstacles
Account for outlets, switch plates, pot filler locations, and any other obstacles. We prefer horizontal outlets near the counter because they’re easier to hide behind small cuts. In our layout, starting with a half tile on the bottom made outlet cuts much easier because they fell along tile edges rather than in the middle of a tile.

4. Plan Pattern Placement Side-to-Side
Measure and level the wall horizontally as well, and consider laying out the first row in place to confirm where seams will fall. Our goal was to center the pattern on the window and sink; by aligning a seam beneath the window we could use a half-ish tile on the chimney side and a full tile on the other, which balanced the look despite wall irregularities.

5. Double-Check That It’s Level
If you plan to use the countertop as a guide for the first row, confirm the countertop is level—at least relative to nearby horizontal elements like cabinet bottoms or window sills. For runs that span gaps (behind a stove or across a doorway), draw a true level line on the wall and reference it as you set each row so your pattern stays visually straight.

6. Cut Your First Row Before You Start
Cutting the entire first row to the same height before installing anything saves time and reduces stress while adhesive is drying. If your wet saw has a guide, lock it and batch-cut the pieces you need. You’ll still trim around outlets and corners later, but pre-cutting gets the major work out of the way.

7. Protect Your Work Area
Cover counters and nearby floors with a protective layer like red rosin paper. It has a moisture barrier that helps prevent adhesive or grout from soaking through. Run painter’s tape along the counter first so the protective paper lays precisely where it should without interfering with later tile coverage.

8. Trim Molding Interferences
If window sills or moldings block a clean straight edge, carefully trim or notch them so tiles can slide behind rather than requiring craggy edge cuts. A Dremel or similar tool makes this quick and leaves a cleaner finish; if you prefer not to trim, you can also cut tiles to fit, but trimming molding usually gives a neater result.

Taking the time to plan and prepare always speeds the installation and improves the final appearance. There have been times we rushed and ended up with small slivers that cheapened the result—this time the layout, cuts, and patience paid off, even with a complicated patterned tile and a few tricky spots around a window.

We still have a few small items left—beadboard treatment for the stove wall, floating shelves, and styling the cabinets—but the backsplashes are essentially done and we’re thrilled with how they turned out.

*This post contains affiliate links*








