Objectales

Popular

DIY Paver Patio: Step-by-Step Installation Guide

featured 35853

Finished Paver Patio: The Final Steps, Costs, and What We Learned

Hallelujah — the patio is done!

how-to-add-a-paver-patio

I finally caught my breath, my muscles stopped protesting, and now I can tell the rest of the story. We left off with me collapsed on the mostly-laid pavers late on Friday night. After taking Saturday off for family time and a little early Mother’s Day fun, I planned to spend an hour or two finishing the edge cuts on Sunday. That short plan turned into a marathon — seven or eight hours of cutting and fitting.

img 35853 2

Curved edges mean lots of cuts. I thought my tiling experience would make this easy, but paving stones are a different beast. To determine each cut, I laid a full stone against the border pavers (the border is often called a soldier course) and penciled the overlap line where the cut should be.

img 35853 4

For cutting I used a wet saw my dad lent me. It had served me well on previous jobs, but it wasn’t ideal for these thick, roughly 2.5-inch pavers. The blade couldn’t cut all the way through in one pass, so I often had to make two passes — flipping the stone and cutting from the other side — and sometimes more when the saw’s housing blocked the stone. For a few long cuts I had to run the piece through the saw multiple times. After slicing as far as the blade would go, I finished the break with a hammer and screwdriver to knock out the middle section the blade couldn’t reach.

img 35853 6

Multiply two to four cuts by the 50+ stones that needed trimming and you start to see why it was such a slog. By hour three I was seriously eyeing a larger wet saw, but I stuck with the borrowed one. When a cut fit, I set the piece in place and tapped it down gently with a rubber mallet so it sat level and secure in the sand bed.

img 35853 7

Despite the hassle, seeing the border come together was rewarding. The sand I later brushed into the joints also helped hide some imperfections in the cuts.

img 35853 8

By the end of Sunday I finished the cuts and even tightened a sagging gate that would have scraped the new stone if left alone.

img 35853 9

Here’s the patio before the joint sand was hosed off; the lighter edge pavers just had wet saw dust on them.

img 35853 10

And here I am, covered in wet saw spray — goggles saved my eyes, but I should have had a mask. Those yellow stains on my hands came from wet work gloves.

img 35853 11

About the pattern: some call it an “I pattern,” others a “K pattern” — we like to call it a family of H-shaped modules formed from two 6×9 pavers and four 6×6 pavers, flanked by more 6x9s. It reads like organized chaos: a repeating pattern that still feels random. We chose it to match the driveway pavers and because once we placed the first few modules, it was straightforward to build outward from them.

img 35853 12

Monday was the final major push: sweeping paver sand into the joints to lock the stones and prevent shifting. The basic steps were simple — dump sand on the surface, sweep it into the joints, and mist the area so the sand settles. In practice it required repeating the steps several times. The initial misting made the sand slushy and it slid out of some joints, so I repeated the sweep-and-mist cycle and did touch-ups until the joints looked even. When it dried the color evened out from a wet orange-y hue to a complementary gray.

img 35853 18

If you have the budget, polymeric sand is a good splurge — it hardens and helps prevent weeds. We chose standard paver sand to save about $100; it worked well at our last house and seems fine for now. If we ever decide to upgrade, we can wash out the sand from the joints and replace it with polymeric sand later.

After the joints were set, I backfilled the edges with soil to hide the plastic edging. I forgot to photograph the finished borders, but the result was clean and finished. Before-and-after shots of the liriope along the edge show the transformation well.

img 35853 19

img 35853 20

Then came the fun reveal with temporary furniture pulled from around the house. We sold our old patio set before moving, so this staged setup is a mix of sunroom and basement pieces, not yet weather-proof. The furniture helps with scale and imagination — we’re already picturing an outdoor living room with a daybed or loveseat, a coffee table, and a small play area for Clara.

img 35853 21

Clara has already been enjoying the space, tapping chalk sticks together and testing hopscotch (she only tried to eat the chalk twice — progress!).

img 35853 24

The grill, which has been tucked in my basement since the move, finally has a home on the new patio. I’ve used it sparingly so far, but the new spot should encourage more backyard cooking. Sherry’s “crowning jewel” — a small ceramic bird feeder she found for $9.99 — looks much better out here than sitting on the bathroom counter.

img 35853 26

img 35853 27

We finished just in time for Clara’s birthday party, and now we’re hoping for good weather. I joked that finishing the patio might have jinxed us into rain, but fingers crossed I’m wrong.

Here’s a rarely seen angle from the lower patio looking up at the upper patio and the sliders — the new lower patio gives us space for seating and the grill that the upper area couldn’t accommodate.

img 35853 29

We estimate this whole project took about 30 hours from planning to clean-up. Your time will vary based on curves, demolition surprises, and how much help you have. Here’s the final budget breakdown:

  • 300 square feet of Cottage Stone pavers (Southside Building Supply): $621
  • Heavy-duty plastic patio edging and spikes (Southside Building Supply): $69
  • Paver sand (Southside Building Supply & Lowe’s): $107
  • Gravel (Southside Building Supply): $240
  • Delivery for pavers, sand, and gravel (Southside Building Supply): $145
  • Miscellaneous supplies (stakes, line levels, nylon string, hand tamper from Home Depot): $40
  • Weed block fabric & crampons (Home Depot): $30
  • Grand total: $1,252*

*We actually paid $1,332 but got an $80 deposit back when we returned the empty bags for gravel and sand.

Our original under-$1,000 plan was optimistic, but doing it ourselves saved roughly $4,000 compared with contractor estimates for curved work (quotes we saw started around $5,000). It was a lot of sweat and sore muscles, but we’re happy with the result. Would I do it again tomorrow? Not quite — I need a little recovery time first.

For anyone tackling a similar project: take your time measuring and planning your cuts, consider investing in the right saw if your pavers are thick, and decide early whether polymeric sand is worth the extra cost to reduce future maintenance. The finished patio gives us about 300 square feet of usable outdoor living space that we’re already enjoying.