How to Prime Your Wood Paneling for a Smooth Paint Finish
Here’s the long-awaited update on the kitchen paneling project, written up in plain English and with the key takeaways up front for anyone planning to paint wood paneling. If you’re weighing removal, drywall, or paint, this will help you decide—especially if you want to avoid strong fumes by using low- or no-VOC products.
We considered removing the paneling, but that would have meant taking down and rehanging all the cabinets that are mounted in front of it, and likely uncovering unknown issues behind old plaster walls. Drywalling over the paneling was another option, but it would add a lot more time and cost because we’d have to work around the cabinets. In the end we chose to paint the paneling, as we’ve done before in our den with great results. Painted paneling keeps the grooves as subtle texture, but you can fill them with caulk or putty if you prefer a smooth surface.


This time the main difference from our last painted-paneling project was the finish method: we tried to prime and paint the kitchen using low- or no-VOC products to reduce harmful fumes, since we work with paint and caulk frequently and now have a baby at home. That decision made the job take longer than an afternoon, but we felt it was worth the trade-off for better indoor air quality.


Step 1: We wiped down the paneling, exposed beams, and trim with a damp cloth to remove dust and grime. Some people use TSP for a more thorough clean, which is fine if the surface is greasy. We didn’t sand; sanding is only necessary when the surface is rough, splintery, or finished with a glossy shellac.
Step 2: We removed the vent and outlet covers because we planned to replace them anyway—swapping out bisque covers for fresh white ones is an easy update.
Step 3: We applied a first coat of Olympic No-VOC primer to the trim, beams, and paneled walls. About three hours went into that initial coat. Early on we noticed bleed-through: the orange-brown wood stain started seeping through the primer in several spots, which is the problem that stain-blocking primers are designed to prevent.


Primer doesn’t need to look perfect, but persistent wood-bleed is a showstopper. We tried a second coat of the same Olympic No-VOC primer on the worst spots, but the orange seepage remained.

Step 4: We switched strategies and added a coat of Behr Primer + Paint (white semi-gloss) that we already had on hand. It is low-VOC and thicker, so we rolled it on over the trim, beams, and walls. That helped but did not fully stop the bleed-through in all areas.
Step 5: Back to the store we went, and this time we bought Kilz Clean Start No-VOC primer labeled as a stain blocker. We applied a full coat across everything: trim, beams, and paneling.

The Kilz Clean Start did the trick. After that coat the bleed-through was under control and we could finally move on.
Step 6: We painted the trim and beams with the Behr semi-gloss paint. Painting over the primer as soon as possible is a good idea because primer attracts dust and can become hard to clean if left unsealed. The Behr paint had excellent coverage over the Kilz primer and left a clean, glossy finish.

Step 7: We removed the painter’s tape while the paint was still slightly wet for crisp lines; leaving tape on until everything is fully dry risks peeling paint. Where the tape stuck to painted edges, we carefully cut along the tape with a utility knife to avoid pulling paint off.
Step 8: About 48 hours after we started priming, the trim, beams, and most of the surfaces were primed and painted. The trim looked noticeably brighter because it received semi-gloss paint rather than flat primer.

Our takeaway for painting paneling with low/no-VOC products: plan for extra time. If you want to avoid oil-based stain-blocking primers, be prepared to apply 2–3 coats of a no-VOC stain-blocking primer such as Kilz Clean Start, followed by two thin, even coats of latex paint. It’s possible that layering primers helped in our case, but the Kilz product was the one that finally stopped the wood stain from bleeding through.
If you prefer the traditional route, one coat of an oil-based stain-blocking primer followed by two thin coats of latex paint is the standard professional approach. But if you’re prioritizing indoor air quality around children or pets and choose low/no-VOC products, give yourself a couple of days and expect more coats and patience.
We’ve had good results with other rooms using a no-VOC approach—our living room trim was painted with Olympic Premium no-VOC paint and has not shown bleed-through after several months. Rarely, wood-bleed can appear weeks or months later, so keep an eye on finished surfaces and be prepared to spot-prime and repaint if necessary.
In short: painting paneling without VOCs is possible, but it can take longer and may require several primer coats. If you’ve tried this technique, or if you’ve ever had to apply multiple coats of primer or paint to stop bleed-through, we’d love to hear what worked for you. It’s always helpful to commiserate and swap tips when a project drags on longer than expected.
P.S. For a detailed step-by-step guide on painting wood paneling the more traditional way, see our previous post titled “How to Paint Wood Paneling.”








