Objectales

Popular

DIY Reupholster a Rocking Chair with Fabric and Nailhead Trim

featured 39861

DIY Rocking Chair Reupholstery: Part Two

I’m back with part two of the rocker revival. Quick reminder from yesterday’s post: this project was a little chaotic, improvised, and experimental. I followed advice from readers, searched tutorials, and borrowed tips from a friend who reupholsters for fun. It wasn’t a museum-quality restoration—just a $25 Craigslist find—but the results were hugely satisfying. Here’s how I tackled the most intimidating parts of the project.

After finishing the seat and refinishing the frame, the scariest task remained: covering the opening at the top of the chair so it looked finished on both sides. I worried about the structural integrity and the look, but after reading a lot of recommendations (including this post) and talking to my reupholstering friend, I chose a surprisingly common solution: heavy-duty cardboard panels reinforced with batting and fabric.

img 39861 1

The process began by making templates from cardstock to measure the opening precisely. Once I was sure the size would cover the rough interior frame, I traced the template onto heavy-duty cardboard saved from an Ikea file cabinet box.

img 39861 3

I cut the cardboard panels and padded them with one layer of extra-loft batting (the seat used more layers for comfort, but the chair back only needs enough padding to support leaning). I stretched fabric tightly over the batting and used duct tape temporarily on the back to hold everything in place before permanently securing it with staples through the panel into the wooden frame.

img 39861 4

Cardboard sounds fragile, but once wrapped in batting and fabric and stapled every quarter-inch into the frame, the panels became very rigid and durable. They still had just enough flexibility to follow the slight curve of the frame, which made installation much easier than if I’d used a completely inflexible material.

img 39861 5

img 39861 6

Once the panels were stapled in place, the visible staples along the edge presented a new aesthetic dilemma. I briefly considered glued trim but didn’t like how contrasting trim would read against my fabric, and I worried about durability. Instead I decided to use upholstery nail heads to cover the staples for a cleaner, more finished look.

img 39861 8

I removed each staple one at a time with a flat-head screwdriver and replaced it with a nail head, hammering each into place. Initially I tried to place the nail heads close together, but the result looked crowded and uneven. Spacing them further apart—roughly the same distance as the original staples—created a cleaner, more balanced look.

img 39861 13

Tip: work around the chair, removing a staple and adding a nail head as you go, rather than removing all staples at once. Using a small scrap of cardboard or paper as a spacer helps keep the nail heads evenly spaced.

img 39861 12

The studding step is physically demanding—hammering takes time and energy, and some nail heads bent while being driven in, which meant waste and frustration. I went through a few extra boxes to account for bent studs, but spacing them out improved the final look dramatically and made the chair feel more polished and expensive.

img 39861 17

I added some matching studs along the wooden rail under the seat to visually balance the upper panel detail. The shiny studs on fabric paired with the slight gleam on the bottom trim give the chair a cohesive, finished appearance. I still have to add studs to the back panel, so more hammering is in my near future.

img 39861 20

For now, the rocker is cozy and smooth to use. We’ve been trying different pillows to see how it reads in our bedroom and considering moving it to the office for Clara’s reading time. The transformation from that original Craigslist find to this refreshed piece is dramatic and satisfying.

img 39861 22

Budget breakdown:

  • Craigslist rocker: $25
  • Extra-loft batting (JoAnn, with coupon): $6
  • Staple gun: $0 (already owned; approx. $19 new)
  • Oil-rubbed bronze spray paint (Home Depot): $7
  • Heavy-duty cardboard: $0 (leftover packaging)
  • Kravet fabric (clearance remnant at JoAnn): $4 for two yards
  • Nail heads (JoAnn): $6 (five boxes at $1.50 each; used coupons)
  • Total: $48

One small win: the Kravet fabric I found on clearance could have cost much more retail, so finding a remnant saved a ton. All told, this project proved that thoughtful DIY upholstery—using inexpensive materials like reinforced cardboard panels, batting, and well-placed nail heads—can deliver a comfortable, professional-looking result without breaking the bank.

Have you ever tried the cardboard-panel trick or reupholstered a chair? I’d love to hear about your process or any tips for tackling larger pieces like a wingback. Good luck if you’re taking on a furniture makeover—patience and a few extra supplies make a big difference.

Psst—winners from this week’s giveaway were announced. Click the link in the original post to see if you won.