Objectales

Popular

Remove Old Shower Tile Border Without Damaging Surrounding Tile

featured 47879

We’re no strangers to removing unsightly trees—just not the tile kind. Earlier renovations included taking out dangerous dead trees from our first house’s front yard, so ripping out this particular “forest” in our bathroom felt like another sort of cleanup mission. The difference? These trees were printed on tile, encircling the entire room.

img 47879 1

The bathroom’s beige-on-beige palette was never our favorite, but most of it was unobtrusive—until you meet the repeated tree border. It’s the kind of pattern that loops through your head every time you walk in: think The Lion King’s opening tune on repeat. We decided it was time for a practical, modern update: removing the border and replacing it with clear glass subway tile to freshen the space and break up all that monochrome.

img 47879 2

After looking at local tile shops and big-box stores we found clear glass subway tiles at The Tile Shop—a glossy, reflective alternative to traditional white subway tile. They were the right size and would blend with the other updates we’ve made to the bathroom, like painting the trim and swapping out the beige toilet. When held next to the old border, even a single glass tile modernized the look: the clear glass reflects colors in the room, so it adapts and livens the space rather than demanding attention.

img 47879 3

We only needed about $50 worth of tile to redo the entire border, especially after a 10% discount. The shopping run was quick aside from repeatedly pulling our toddler Clara away from display showers—she was obsessed with crawling in and flopping down inside them.

img 47879 4

Although the tiles themselves were affordable, the project required a tool to remove the old tile and grout. We bought a Dremel MultiMax with a grout-removal attachment. The tool and attachment added roughly $130 to the cost, but we considered it an investment for future projects—already useful for other tasks since then.

img 47879 5

Using the oscillating Dremel with the grout head felt straightforward. We slowly pressed the vibrating blade into the grout lines, letting the groove between tiles guide our cut. The attachment effectively removed grout without aggressively scratching neighboring tiles if we slipped, which reduced the risk of additional damage.

img 47879 6

John tried the tool first—new-tool enthusiasm in full force—but I joined in too. Removing the grout was time-consuming, though the grout-cutting approach was far less messy and invasive than trying to pry the tiles off whole without first freeing them. Once the grout was out, we expected each tile to pop free easily, but the first tile only chipped. That small chip ricocheted and nicked my neck, so we were grateful for safety glasses. After a few careful taps with a screwdriver and a hammer, we finally got under that first tile.

img 47879 8

With more prying the first tile came off, and then the rest followed. It became clear the tiles had been set on drywall rather than cement board. That’s not ideal for tile backing, but because this wall is beside the toilet rather than inside the shower, we decided the installation underneath was acceptable and didn’t require replacing the substrate.

img 47879 9

The process got messier and dustier than we hoped, but the next rows came off more quickly. Tiles that were mounted on drywall paper and thinset tended to release more easily than those adhered to cement. Still, cutting out all of the grout proved the most time-consuming part of the demo.

img 47879 11

After about 2.5 hours—coinciding perfectly with Clara’s nap—we had removed the entire border without further injuries. We took a moment for high fives and assessment. The floor looked like a small construction zone so we spent another half hour sweeping and wiping down the room, then took our showers in the hall bath while we prepared to install the new tile.

img 47879 13

img 47879 14

img 47879 15

Removing the tile border in one afternoon felt like a solid DIY win. The next step—setting the clear glass subway tile—was ready to begin, but we paused to finish a few prep tasks and take photos. If you’ve removed tile before, did you use an oscillating tool like a Dremel? How did the process go for you—efficient and satisfying, or messy and maddening? We’re happy to report a DIY victory and plenty of high fives.

Psst—To follow this bathroom refresh from the start, see this planning post, this painting post, this light-swapping post, this art and trim-painting post, this toilet-updating post, this window frosting and shampoo wrangling post, and this toilet selling/buying and door-cutting-down post.