DIY Upholstered Headboard: How to Build the Frame
We owe a big post about our trip to the Haven conference and Atlanta, but we’re driving home today after visiting dozens of inspiring houses, touring thrift stores with Katie B, and even hosting a makeshift backyard wedding for Clara and Will. Before we left for Atlanta, we managed to start a headboard for our newly rearranged master bedroom. With Ed the Bed now minus his posts, we focused on creating a new upholstered headboard to accompany the darker floors and dresser we’re planning.

We wanted a headboard that combined a soft, cushioned surface with a structured base—something upholstered over wood or woven material. Lately we’ve been doing a lot of reading in bed, and the room’s new layout felt cozy but lacked that soft, layered feeling. Rather than our usual stretched-canvas method, we designed a headboard that would wrap around what was left of Ed’s original posts and hide them, creating a seamless look once upholstered.
Our plan used a sheet of plywood and a few 1×3 boards to form a frame that would encase the remaining posts. To make the concept easier to visualize, imagine simple blocks of wood forming a rectangular headboard that curls around the posts so they disappear behind the new structure.

Clara turned out to be a great helper at Home Depot, even when the big saw used to cut our plywood fascinated and intimidated her at the same time. We bought a 5/8″ sheet of plywood cut to 65″ x 36″, and had the store slice it in half so it would fit in the trunk of our small car. Splitting the sheet also made it easier to handle at home. Our total for the plywood and two 1×3 whitewood boards was only $22.

At home I laid out all the pieces to show how they would assemble: the two side pieces that wrap around the bedposts, and two braces across the middle to join the two halves of the plywood. These middle braces compensate for cutting the plywood and create a sturdy back panel.

I attached the side pieces with pocket holes using a Kreg Jig for a clean, strong connection, and secured the center braces with a few screws driven straight into the plywood.

Here’s the headboard fully assembled—the view shown is the back side that will sit against the wall. Initially I assumed it was ready for upholstery, but Sherry wisely suggested we bring it into the room first to check the scale and fit before adding batting and fabric.

It fit width-wise, but in person the height looked a little too tall for the bed’s modern, low-profile lines. The headboard felt top-heavy and a bit traditional compared with the clean, contemporary bed frame. After holding up paper templates from across the room to test different heights, we decided to trim about 5 inches off the top.

We used a circular saw to make the cut without having to disassemble the entire piece. Back in place, the shorter headboard feels much more balanced with the bed and leaves space above to hang art or other layered elements for a cozier bedroom composition.

The close-up of the side shows how the 1×3 wraps just enough to conceal the remaining post. Once the entire piece is upholstered, this wrap-around design will read as one continuous, wider headboard rather than revealing any awkward posts behind it.

Sherry will cover the upholstery steps in a follow-up post—there were too many photos to upload before we left. For now, here’s a preview of the fabric we chose: a free-form botanical print that echoes the turquoise tones in the rug without competing with its geometric pattern. The mix of organic shapes and subtle geometry creates a light, airy effect that complements the room’s modern feel. While the fabric looks busy sitting next to the rug in the photo, in the finished room the headboard and rug will occupy different planes (wall and floor) so they won’t visually clash.

One quick tip from this project: always test the headboard’s size and position in the actual room before stapling on upholstery fabric. Pillows and proportion can significantly change how a headboard reads, so measure and mock it up in place first. Clara thought the whole Home Depot experience—pushing the cart and surviving the loud saw—was an epic adventure, and after an all-day drive with her today we might agree it was an eventful weekend. How about you—any weekend DIY projects, road trips with little ones, or headboard builds to share?








