How to Build a Solid Deck Foundation
Deck Progress: Framing, Flashing, and Railing Prep
“Can’t we just lay some decking already?!” That line echoes a familiar feeling — eager to get to the visible, satisfying work while a string of small but necessary prep tasks still stands between you and progress. After setting all of the joists, we were excited to finally put down deck boards, but several important details needed attention first. The good news: by the end of this update you’ll actually see decking going down, and the project is much closer to finished.

Before continuing we opted for a voluntary framing inspection. Our county’s next required inspection would have been the final one after everything was complete, and we didn’t want to finish the deck only to discover a costly mistake. The inspector we met with was sympathetic to a small detail: I had notched my 4×4 posts instead of using the county’s recommended bracket (their guidance allows notching only for 6x6s). Because our deck is low to the ground and relatively small, he wasn’t worried, and he gave us the green light. His verdict, delivered with humor: “this thing’ll hold up five elephants and about 500 of those (points to Clara through window).”

With inspection approval in hand, the next step was finishing the exposed edge of the deck by adding band boards to tidy up uneven joist ends. This corner is the angled portion of the deck where the stairs will descend, so it required careful miter cuts and a few precise measurements.

I began by trimming the excess from the two angled joists so a 2×8 band board could be attached cleanly. I used a nylon string and a pivot ruler to lay out a 45-degree cut line, then adjusted the circular saw blade angle to slice the joists in place. (Note: the photo below is a staged shot to show the setup; when cutting I keep both hands on the saw.)


The two joists were cut to match, and I trimmed the 2×8 band board to fit, including the corresponding mitered end that sits against the house. I temporarily tacked the band board in place with nails and then secured it with screws for a solid connection.


One end still needed its own band board, so I cut another 2×8 to size with a matching miter and set it loosely in place. Before screwing it down I noticed the girders that supported it stuck out past the deck edge. I intentionally left them long when installing the girders so I could fine-tune the fit later; this was the moment to trim them back.


I cut most of the cross-grids with a circular saw and finished through two stacked 2x10s using a reciprocating saw. With the girders trimmed, the final band board fit neatly against the rim and the angled board, so I secured it with screws and removed a little excess from the angled board for clean, finished edges.


Next up: counter-flashing. One of the conditions that came out of our earlier inspection was to add extra flashing over the ledger boards to keep water away from the house and ledger. On the siding side I slid the flashing under the bottom course of siding and nailed it in place. Where the deck meets brick, I folded a small section and tucked it into a mortar crevice, then ran a bead of clear silicone caulk along the crack to hold the flashing and prevent moisture intrusion. I also bent a small drip lip so water clears the brick rather than running back toward it.


With flashing installed, I paused to think about the stairs and guardrail. Rather than waiting until after decking, I wanted to install any required reinforcement while the frame was exposed. I used spare 2x10s as placeholders to locate stair stringers and the positions for 4×4 guard posts. Where a post sits next to the rim board attached to the house, I bolted a deck tension tie directly to the rim and through the post. For posts away from the rim board, I added blocking between joists and mounted tension ties to either side of that blocking to secure the posts. This method conforms to modern attachment standards and provides solid guardrail resistance.


I drilled bolt holes through the posts and used 1/2″ bolts to attach them to the tension ties, meeting the county’s 36″ railing height requirement. For the angled section I added blocking and tension ties so those posts will be equally secure. I also installed a few joist hangers where joists meet the angled band board for added confidence in the connection.


Installing the hardware and blocking took about two days. Tight spaces made some of the drilling and bolting awkward, and a few pop-up thunderstorms interrupted work, so progress wasn’t nonstop. Still, getting these structural and weatherproofing tasks done now made decking and railing installation much simpler.

And finally: deck boards. We started placing boards and are using a mitered outer frame around the entire deck with a few intentional “zipper” seams inside the field for visual interest. So far the layout looks great and we’re excited to continue. You’ll see more progress photos as the decking continues — the project is really starting to come together.

Now that the prep work is finished, the visible progress pays off. It’s satisfying to move from the nitty-gritty tasks to the final surfaces. What small, unglamorous chores have you checked off recently — paint touch-ups, smoke detector batteries, pulled weeds, or replaced filters? Those little wins add up.








