DIY Wood Plank Ceiling Installation: Step-by-Step
When we decided to install a wood-planked ceiling in our sunroom, I pictured a quick trip to the big box store, grabbing some beadboard, and calling it a day. As it turned out, there are many ways to achieve that classic beadboard look, and choosing the right material mattered more than I expected.

Traditionally, beadboard is made from individual tongue-and-groove planks—similar to hardwood flooring but with a narrow ridge, or “bead,” between each board. There are also full-sheet panel options that mimic that pattern, but panels have pros and cons. They’re often the most affordable choice, sometimes under $1 per square foot, and they can speed up installation. However, large 4ft x 8ft sheets are heavy and awkward on high, sloped ceilings. They also create visible seams where sheets meet, which we didn’t want on our sloped sunroom ceiling.


The vinyl plank option appealed because it resists moisture and won’t rot, which can be a big advantage in outdoor-exposed spaces. But the look often reads a bit plastic and the price was significantly higher—nearly double the panel option—so vinyl didn’t make sense for our budget.
We eventually settled on individual tongue-and-groove wood planks. Buying individual 6″ planks gave us the authentic look we wanted, without artificial seams, and allowed us to transport the materials ourselves. We found a 6″ tongue-and-groove option priced under $1 per square foot, and our final material cost for the project came to $297. It was a bit more than our original estimate, but we preferred investing a little more for a durable, long-lasting result.

Choosing individual planks did mean more work during installation—each 6″ board must be installed row by row, and wood requires protection from moisture to avoid warping or rotting. Since the sunroom’s exterior is already wood and had held up well for decades, we felt confident that properly priming and painting every plank would prevent future problems. That meant priming and painting both sides of every board before installation.

My first painting setup didn’t work well—the plastic drop cloth stuck to the back of the boards—so I switched to drop cloths on the ground with a nylon rope strung between trees to hang the planks. That let me spray 10–12 planks at once: spray the back, flip, then spray the front. We used a handheld paint sprayer for speed; the process still required frequent cleanings and careful handling, but it was faster than brushing every board.

Painting both faces of 120 planks—primer and finish coat—took several two-hour sessions over about four days. We could only dry about 45 boards at a time in our garage, so we worked in batches: prime and paint a group, install them, then repeat. It was tedious and messy, but knowing the boards would be fully sealed on every surface made it worth the effort.

For primer we used Kilz Premium, and we finished with Benjamin Moore Regal Select Exterior in a low-luster finish. The color is a soft, pure light blue called “In Your Eyes.” We wanted a subtle blue that wouldn’t be too bold or cast an unwanted tint into the adjacent rooms. The paint desk recommended that exterior formula for durability against the elements.

Before installing the planks, we reconsidered insulation. Some commenters suggested re-insulating to keep summer heat from transferring through the roof, and initially we reinstalled the leftover insulation. Later, after consulting a framing expert, we learned that insulation placed directly between the roof deck and a finished ceiling with no airflow can trap heat and moisture. Trapped heat can reduce roof longevity and trapped moisture can threaten the beadboard. We removed the insulation to allow airflow and planned to add a row of vents and ceiling fans to improve circulation instead.

Installing the planks felt a lot like laying hardwood floor. Starting straight along the wall is crucial, so I cut scrap wood spacers to ensure the first row was perfectly even. We ran the planks parallel to the long wall so we could attach them directly to ceiling joists spaced every 16 inches. That spacing makes the ceiling sturdy and helps prevent future sagging.

We also staggered seams between rows so the board ends didn’t line up vertically, which improves structural integrity and looks more natural. To minimize visible gaps, we cut matching 45° scarf joints at board ends so they overlap slightly and create a cleaner transition. We made sure seams landed on joists so we could secure both ends with nails.

When hanging each board we applied wood glue along the joists, slid the tongue-and-groove boards into place, tapped them lightly with a rubber mallet when needed, and finished by shooting nails into the joists. The first batch of 45 boards took roughly five hours spread across several days. Once we had the technique down, the pace picked up significantly and the ceiling began to take shape.


After removing the insulation and installing a second batch of planks, the ceiling started to look complete. I carved openings for two future ceiling fans and added a ventilated row at the top to encourage airflow—recommendations that came from our framing expert and that will help prevent trapped heat and moisture.

It’s worth noting that what we installed isn’t true beadboard with carved beads—it’s 6″ tongue-and-groove planks that create a similar look. We chose the simpler plank style because a smaller, detailed bead might have looked too busy across the span of the sunroom ceiling.

We still have a few finishing steps: add trim around the edges, caulk and paint the trim, fill nail holes across the boards, and apply one final protective coat over the assembled ceiling to seal seams against moisture. After that we’ll install two ceiling fans, repaint columns and interior trim with exterior-grade white paint, and move on to tiling the floor and furnishing the space.

Progress feels great—my arms are getting their feeling back—and we’re closing in on the finish line. Here’s the current to-do list:
- Prime, paint, and install the tongue-and-groove ceiling planks
- Add trim around the ceiling, caulk and paint it, and hang two ceiling fans
- Repaint columns and interior sunroom trim with exterior-grade white paint
- Tile the floors with an outdoor-safe, slip-resistant product
- Add rugs, furniture, outdoor curtains, and lighting
- Consider an outdoor fireplace or other long-term upgrades

All in all, choosing individual planks and taking the time to prime, paint, and install them carefully gave us a durable, attractive sunroom ceiling that should hold up for years. If you’re planning a similar project, consider how material choice, sealing every surface, and allowing airflow behind a roof assembly can affect longevity and performance.








