Objectales

Popular

How to Install Under-Cabinet LED Lighting

featured 88854

Under-Cabinet Lighting Installation: Our Laundry Room Spotlight Upgrade

We haven’t added many upper cabinets in our recent projects, so under-cabinet lighting has been rare for us — but we did install it in our laundry room a few years ago, and I recently found photos of the installation I never shared. The process is straightforward and makes a great, budget-friendly upgrade for kitchens, laundry rooms, or any space with upper cabinets where you want better task lighting.

img 88854 1

The cabinets we used were from Ikea, and we originally installed their older GRUNDTAL spotlights. Those are no longer sold, but the newer OMLOPP spotlights are a similar — and in many ways improved — option: they are LED, lower-profile, and include cord-management covers. According to the instructions, the OMLOPP units install almost the same way, so the steps below apply equally well to the newer lights.

img 88854 2

Many people install one spotlight per cabinet, but we wanted the look of a continuous strip of light rather than distinct pools of illumination. The older GRUNDTAL lights were sold in three-packs, so we installed six in total. In hindsight, four or five would probably have been sufficient for even illumination in this small room.

The first step is to unpack the lights and remove the bulb module from each housing, leaving the wiring attached. This exposes the mounting holes you’ll use to fasten the light to the cabinet underside.

img 88854 3

Measure and mark placement before screwing anything in. We centered each spotlight front-to-back and spaced them evenly side-to-side (roughly 10 inches apart). Use short screws — we used 1/2″ screws so they wouldn’t poke through the cabinet interior — then snap the light back into its housing.

img 88854 4

After securing the spotlights, you’ll connect the individual fixtures to the transformer box. With Ikea’s updated OMLOPP system the transformer and power cord are sold separately so you can scale based on how many spotlights you’re installing (one transformer can power multiple fixtures). Wiring the lights to the transformer is straightforward on the older units and the newer ones are even easier — essentially a plug-in connection similar to a phone charger.

img 88854 5

Before tidying up wires, always test the connections. The transformer plugs into a standard outlet and often has a toggle on the cord so you can power the system without calling an electrician. We had ours working within minutes.

img 88854 6

Newer kits include adhesive cord covers to conceal wiring along the cabinet bottom, but you’ll still need a plan for excess cable between the cabinets and the transformer. I used a mix of cord-management hardware: mounting ties (zip-tie style straps with a screw hole) and small wire staples to keep everything tight to the underside of the cabinet. If the provided fasteners are too long, swap them for shorter nails or screws so nothing pokes through the cabinet bottom.

img 88854 8

To hide the bundle of wires and transformer, we wrapped excess cable with a zip tie and secured it with a mounting screw, then ran the main cable along the cabinet corner with wire staples. A shallow cover strip installed across the bottom of the cabinetry conceals the work so you see only clean, continuous lighting from below.

img 88854 9

Our transformer box is mounted behind a small gap at the side of a cabinet, hidden behind an Ikea filler piece. The transformer includes mounting holes for screws, which makes this installation simple. That placement also keeps the power cord hugging the corner as it drops to the outlet.

img 88854 11

A couple of years after the initial install we had an electrician hardwire the power cord to a wall switch. That adds convenience, but it’s optional — the plug-and-switch that comes with the transformer works fine until you decide to hardwire.

img 88854 10

Because Ikea cabinet bottoms are flat rather than recessed, we used a filler strip across the bottom to fully hide the lights and wiring. The cover strip is attached with small L-brackets and sealed with caulk for a finished look. The newer OMLOPP lights are slimmer and include cord covers, which helps reduce the need for large filler pieces.

img 88854 13

Cost-wise, a similar setup today using the newer system would run roughly $75 (about $90 if you include a remote). You can reduce cost by installing fewer fixtures; three lights with a smaller transformer can cost closer to $45.

img 88854 15

Here’s a recent photo of the switch we had installed to make the lights easy to turn on. We use these lights about half the time — the ceiling light is often enough in the small room — but the under-cabinet lighting remains a helpful and attractive upgrade whenever we need focused task light.

img 88854 16

If you’ve been curious about how difficult under-cabinet lighting is to install, this project shows it’s an approachable DIY for beginners: measure carefully, secure the fixtures, connect to the transformer, test, and manage the cords. With a little planning, you can add bright, useful lighting to your cabinets without much expense or hassle.

P.S. For a full summary of our laundry room makeover, including a budget breakdown and source list of finishes and accessories, see our project notes on the room remodel.

*This post contains affiliate links*