Upgrade Fluorescent Lighting to a Pendant Fixture
Updated 2019
We recently removed two old fluorescent fixtures from our kitchen and replaced them with contemporary pendant and flush-mount lights. Each removal required a slightly different approach because, as it turned out, one fixture box was missing and the ceiling simply had wires poking through the drywall. Below are two clear methods for replacing fluorescent lighting with updated fixtures, along with safety tips and finishing steps to make the ceiling look new again.

Removing a Large Fluorescent Light Fixture
We started with the large fluorescent fixture near the stove. This removal was straightforward; follow these steps for a safe and efficient swap.
Step 1: Turn Off the Power
Always turn off the circuit breaker for the light you’re working on — don’t rely only on the wall switch. This prevents someone from accidentally switching the light back on while you’re handling wires. For extra safety, check the wires with a non-contact voltage detector before touching them.
Step 2: Remove the Plastic Shade and Tubes
Pop off the plastic diffuser that usually snaps into place, then remove the long fluorescent tubes and set them aside. That keeps them from breaking while you work.

Step 3: Detach the Metal Panel
Remove the metal cover that hides the wiring. In our case the ceiling wiring came up through the center of the fixture, which made the conversion easier. If the wires enter from one end, you may need additional work to relocate a junction box.

Step 4: Disconnect the Fixture Wires
With the breaker off, unscrew the wire nuts to disconnect the fixture from the ceiling wiring. You won’t need to alter the internal ballast wiring of the old fluorescent unit — just disconnect the supply wires where they meet the house wiring.

Step 5: Unscrew and Remove the Fixture
Remove the large screws at either end that hold the fixture to the ceiling and take the whole unit down. If it’s still in usable condition, consider donating it.


Step 6: Spackle and Paint
If the new fixture won’t cover the same area, fill screw holes and any damaged drywall, then prime and paint so the ceiling looks uniform. This step removes the visual evidence of the old fluorescent fixture.
Installing a Pendant Light
With the fluorescent fixture removed, you can install a pendant, semi-flush, or flush-mount light. If you’re not comfortable doing the wiring, hire an electrician. If you’ve already removed the old unit and followed safety steps, finishing the job yourself is usually straightforward.
Step 1: Trim Excess Wire
Shorten the cord so the fixture sits at the desired height. You can shorten most pendant cords or convert a plug-in fixture to hard-wired by trimming and re-terminating the conductors.

Step 2: Strip the Wires
Use wire strippers to expose the required length of conductor for secure wire-nut connections to the house wiring.

Step 3: Mount and Wire the Fixture
Attach the mounting bracket to the ceiling box, connect matching wires with wire nuts (neutral to neutral, hot to hot, and ground to ground), secure the canopy, and tighten the screws. Restore power and test the light.


After finishing the larger fixture, we moved on to the small fluorescent above the sink. Removing that one revealed that there was no fixture box in the ceiling — only wires protruding through a hole — so the next steps show how we installed an “old work” ceiling box.


Installing an “Old Work” Ceiling Box
An old work ceiling box is designed to be installed into existing drywall when you can’t secure a box to a joist or stud. It uses flip-out wings or clamps that pinch the drywall from behind when screws are tightened. These boxes are intended for lightweight fixtures; for heavy fixtures it’s better to secure a box to structural framing.

Step 1: Turn Off the Power
Double-check the circuit breaker is off before cutting into the ceiling or handling wires.
Step 2: Mark the Opening
Trace the box template onto the ceiling, centering it over the wires. If you’ve lost the template, make a paper guide slightly smaller than the box lip so the lip can rest on the drywall.

Step 3: Cut the Hole
Use a drywall jab saw to cut the opening carefully so the wires will feed through the center of the box.

Step 4: Feed and Trim the Wires
Pull the house wires through the back of the box and trim them to the needed length before making final connections. Again, be sure power is off.

Step 5: Secure the Box
Tighten the face screws so the wings flip out and clamp the box to the drywall.

Step 6: Install the Lightweight Fixture
Connect the fixture wires, secure the canopy to the box, restore power, and enjoy the new light. Old work boxes can support many lightweight pendants and shades, but for heavier fixtures use a box anchored to framing.

As a final update, we switched the home to LED bulbs for energy savings and longer life. LEDs now provide warm, natural light and use significantly less energy than old incandescent or fluorescent bulbs.
Once the fixtures were in, we primed any exposed drywall and painted the ceiling with a flat white to match trim and freshen the whole room. The paint made a noticeable difference, brightening and unifying the space.


- Remove wallpaper
- Move fridge cabinet forward
- Remove upper cabinets on window wall to prep for open shelves
- Reinstall crown molding
- Prime and paint pantry and garage door
- Prime and paint trim, crown molding, and baseboards
- Prime and paint paneling
- Prime and paint the walls
- Replace microwave and consider relocating countertop unit
- Install a range hood to brighten the cooking wall
- Patch, prime, and paint the ceiling
- Replace fluorescent fixtures with updated lights
- Center the light over the dining table
- Hang floating shelves on the window wall
- Paint the cabinets
- Update cabinet hinges and knobs
- Consider a rug for the eat-in area or peel-and-stick tiles
- Install curtains or window treatments
Removing outdated fluorescent lights and installing new fixtures is a relatively affordable project that greatly improves the look and feel of a kitchen. With basic tools, a little planning, and attention to safety, you can complete the swap and enjoy brighter, more attractive lighting.

*This post previously included an affiliate reference.








