Objectales

Popular

DIY Drywall: How to Finish Walls Like a Pro

featured 42224

We’re excited that the wall section and contractor have finally cleared out, but there’s still a fair amount of work before this opening feels finished. If you like raw construction chic, feel free to admire this as-is:

img 42224 1

Before I dive back into the renovation details, a quick note about the contractor: neighbors have asked for his contact info, and now that we’ve worked with him and were very pleased with the result, we’re happy to share. He’s a licensed Class A contractor (not a handyman), so he handles major structural jobs like removing walls and building additions. His email is [email protected].

On to the next steps for the opening. We left the protective plastic up because drywall was next and drywall sanding can be dusty. We don’t claim to be drywall pros—my least favorite part of our bathroom renovation was the drywall—but this job felt small and straightforward enough to tackle ourselves. We only needed a strip across the top of the doorway on the dining room side to cover the exposed header, plus a few pieces around the half-wall.

img 42224 2

On the kitchen side the half-wall will be finished with wood paneling, so we had the contractor leave the demolition scraps. I measured, marked, and cut the pieces with a small jigsaw—super quick and straightforward.

img 42224 3

I even set a cabinet against the new half-wall before finishing the drywall. Steve suggested doing that so I could see the studs and screw into them easily and accurately. Note: there will be a 12″ counter overhang behind this peninsula with stools tucked underneath, so the half-wall won’t be very visible from this angle once it’s complete. We’ll also top the half-wall with a chunky wooden ledge for both balance and function.

img 42224 4

Already looks a bit more finished, right? Well, sort of.

img 42224 5

But I had to tackle the practical problem of getting drywall home. A full 4×8 sheet won’t fit in our Altima, and renting a truck felt silly for a $14 purchase. So I followed Steve’s advice: cut the drywall down to size at the store. Yes, I set up in the Lowe’s parking lot with a tape measure, chalk line, razor blade, yardstick, and a towel to keep the car clean-ish. Forty-five minutes later I’d sliced and snapped the pieces I needed.

img 42224 7

The dining room wall required two panels of drywall in thickness, so I cut two of each size to match. I managed to fit the half-wall pieces in the trunk and the longer header pieces tucked through the middle of the car. Success.

img 42224 8

img 42224 9

img 42224 10

Once home, we could jump right into hanging the cut-to-size drywall. Sherry held one edge while I tacked a few screws to keep it in place, and then she documented the process by taking photos.

img 42224 11

However, a small measurement mismatch slowed us down. Even though we were careful, our new doubled-up drywall sheets were slightly thicker than the existing doubled-up drywall. Even a small thickness difference is noticeable under light, so I removed one panel and shimmed the remaining piece to get it flush.

img 42224 12

I used wood shims and, creatively, stacked paint stir sticks screwed together to match the thickness of furring strips. The header and framing are solid, so the shimmed drywall held firmly. You can see a bit of the shims protruding near the bottom—nothing a bit of trim won’t hide.

img 42224 13

I repeated that process on the larger half-wall panel, carefully getting everything as flush as possible before screwing it in. We’ve accumulated an embarrassing number of paint stir sticks over the years, so they came in handy for this small drywall shim solution.

img 42224 14

The small end-cap piece was a single sheet since it didn’t need to match any existing thickness; we secured it to the wood framing and used metal drywall corner strips to create a crisp edge. Those strips aren’t strictly designed for a join between paneling and drywall, but a bit of improvisation kept everything neat—more on the final look later.

img 42224 15

Hanging the drywall was done with only that one hiccup. Next came the mudding and finishing. I passed that task to Sherry since she has a steadier hand for taping and smoothing than I do. She broke out a full set of spackle knives and got to work taping seams, applying joint compound, smoothing, letting it dry, sanding, and repeating.

img 42224 16

Sherry did three coats in most spots to ensure a seamless finish. For one narrow crack near the crown molding she chose caulk instead of trying to get mud into the tight space with a putty knife—sometimes a simple solution is the best one.

img 42224 17

img 42224 18

The corner pieces we installed around the half-wall turned out better than I expected. Once primed and painted, the joint between the drywall and wood paneling will read as a clean, durable edge. I didn’t get a photo from the other side yet, but we’ll share that later.

img 42224 19

It definitely looks more finished than it did this morning, but it’s far from done.

img 42224 20

Right now the opening reads a bit unfinished because:

  • there’s no trim to tie it into the surrounding doorways
  • baseboards end at the half-wall and aren’t complete on either side
  • there’s no wooden ledge yet to add function and visual balance
  • the peninsula and counter slab behind the half-wall aren’t installed
  • lots of surfaces still need primer and paint, which makes everything look rough

The whole arrangement is out of context for the moment, but it will come together. In case you’re new here, here are the reasons we chose a half-wall rather than a full open peninsula:

  • we didn’t want the peninsula to look like an afterthought stuck in the doorway
  • the half-wall will visually and structurally ground the peninsula so it feels supported
  • we already have storage with built-ins in the dining room, so extra cabinets would be redundant
  • a new built-in near the existing built-ins would feel crowded
  • the half-wall means a cleaner threshold without an awkward strip of flooring between rooms

Next up: installing the door jamb, building the wooden ledge on top of the half-wall, adding trim and finishing baseboards, then primer and paint. After that, the peninsula and countertop go in and the space will finally start to feel finished. We’ll share updates as we make progress.

Sherry also contributed to a lively design discussion about trends and what’s in or out—fun to read and think about different perspectives.