Objectales

Popular

How to Build a Waterfall Edge Countertop

featured 65539

Call me T-Boz — let’s talk about our new laundry-room shelf, which features a waterfall edge and a light natural stain. It was a straightforward DIY using solid wood panels and a stain/sealer combination to get a butcher-block look.

img 65539 1

We stepped away from our usual mocha stain after seeing rooms that paired light cabinets and tile with natural wood to add texture and warmth. Here’s a wider view—ignore the missing trim, crown, toe kick, and hardware for now. Those finishing touches are coming, along with some final waterfall tweaks.

img 65539 2

Before the shelf, we had to re-install the appliances. It wasn’t complicated—mostly re-attaching what we removed during demo—but one tricky bit was positioning the washer pan and connecting it to the overflow drain. There aren’t a lot of detailed guides for that step, so we’ll summarize what worked for us. A washer pan sits under a second-floor washer so a leak drains away instead of flooding the upstairs and damaging the floor framing below. It’s a preventive measure that can save a lot of hassle, especially for slow leaks you might not notice right away.

img 65539 3

Our contractors and plumbers gave mixed opinions—some said a pan and overflow aren’t required by code in our area, and one even wondered how much it helps for a violent, gushing failure. Others pointed out that pans catch those subtle, watchdog-worthy leaks, so we had the plumbers install one while they were already moving the other hook-ups (it was included in the $375 plumbing fee). Note: we also added an extra outlet pair in the room, which you can see in this shot.

img 65539 3

As we installed various flooring layers we cut around the overflow drain, which you can spot in earlier tiling photos. The plumber set the drain so we could slightly raise or lower the pipe in the garage ceiling below—a small detail that prevented us from constantly tripping over it while working.

img 65539 4

When the plumber left the pan, he gave basic instructions for attaching it, but first we had to finalize appliance placement so the pan sat in just the right spot. The washer could go almost flush to the back wall, but the dryer needed some extra space for semi-rigid ducting so it can be pulled away without stressing the vent connection. That ducting made the dryer sit about 8″ from the wall in our setup.

img 65539 5

There are systems that recess dryer ducting into wall cavities, but most require a vertical vent up to the ceiling; our vent runs straight out under the attic stairs, so those systems weren’t compatible. Because we expected the extra depth behind the dryer, we planned the shelf to accommodate it. After finalizing dryer placement, we set the washer to match that depth and marked the floor with tape so we could place the pan precisely.

img 65539 6

To cut the hole in the pan for the drain, the plumber suggested a simple trick: squirt mustard on the pipe, press the pan in place, and drill where the mustard marked it. We traced the mustard mark with a Sharpie to avoid working with the lingering smell while we drilled.

img 65539 8

Once the pipe fit through the pan, we were told to “silicone caulk the heck out of it.” I wanted a more secure bond, so after consulting another plumber and a hardware-store expert, I used a waterproof epoxy (marine-grade Loctite) to glue the pipe to the pan, let it cure overnight, trimmed the excess pipe flush with a Dremel, and then sealed the joint thoroughly with silicone caulk for redundancy.

img 65539 9

Hoisting the washer into the pan was a two-person job—no glamorous photos, just strained faces and teamwork. We also adjusted the dryer feet so both appliances were level and lined up at the front and top. When everything matched, we did a little celebratory whoop: we finally had a working washer and dryer again.

img 65539 10

On a related note: after our Ikea cabinet install, some readers recommended soft-close add-ons. We planned to pick them up later, but the store included them in our order and they showed up with our under-cabinet lighting hardware. The drawers and doors are now far less likely to slam—definitely worth the upgrade.

img 65539 11

Back to the shelf: we built it before tiling so we could position the tile precisely around it. The shelf and counter came from two solid 2 x 4′ butcher-block-style panels from Lowe’s. We used one panel for the shelf—cut into two 9″ strips and joined with a Kreg jig—and the other for the counter—cut into two 18″ pieces and joined the same way. I left the counter overhang long until after tiling so the final fit would be perfect.

img 65539 12

The waterfall edge was made by cutting the shelf end at a 45-degree angle, then reattaching it at a right angle with glue and nails to form the drop. The shelf is removable to allow access to appliance hookups and rests on four heavy-duty brackets that are anchored into studs in key spots so washer vibration won’t knock things off. So far we’ve run several large loads and it’s been solid.

img 65539 15

For the finish, we tested several stains on scrap pieces. Sherry pre-conditioned some samples, then we tried four stain colors (two Minwax, two Rustoleum). Varnish made some samples too yellow, so we discarded those. Ipswich Pine and Summer Oak were too pale and Wheat had too much red; Golden Oak gave the warm, natural tone we wanted.

img 65539 16

We applied one coat of stain followed by three coats of Safecoat Acrylaq to seal the wood. We used that same sealer on a vanity top in a previous house and it held up well to moisture, so it felt like the right choice for a laundry room surface.

img 65539 17

I’m really happy with how it turned out. The shelf brings warmth and texture to the room’s light, bright foundation of cabinets and tile. It looks a bit sparse now, but we’re just starting to add functional elements and decor.

img 65539 18

We still have a few finishing tasks on this wall, but the door is hung and the glass door to the future bunk room is in progress. We’ll also add a laundry sorter, a pull-out drying rack, and a wall-mounted ironing board on other walls, so expect more updates soon.

img 65539 19

Budget update:

  • Framing (labor & materials): $360
  • Electric (labor & materials): $400
  • Plumbing (labor & materials): $375
  • New dryer vent: $87
  • New HVAC vent: $59
  • Drywall & insulation: $298
  • Drywall mudding: $84
  • Sub-floor materials: $30
  • Tiled floor: $451
  • Ikea cabinets & under-cabinet lighting: $862
  • Appliance re-install: $15
  • Tiled marble accent wall: $281
  • Shelf & counter (including stain testers & stain): $97
  • TOTAL: $3,399

We received two contractor estimates for framing, electrical, plumbing, and drywall at $3,250 and $5,000, so it’s reassuring to be on the lower end after adding tile, cabinets, and the shelf. We’re roughly double where we were at our last check-in because we tackled major costs like tile and cabinetry, but once we finish doors, trim, and crown molding we should be close to wrapping up the big expenses. If all goes well, this reconfigured laundry and bunk-room entry could come in under $4,000.

img 65539 20

Maybe I shouldn’t tempt fate, but at least we can say we’re headed in the right direction—and under the six-figure renovation nightmares, thankfully.