How to Hang a Door: Step by Step Installation Tips
DIY Door Jamb Installation: How We Hung Two Interior Doors
Hope you had a great Labor Day — we split time between family and house projects, which is our ideal balance. This week is busier than usual with book-related commitments, but we made steady progress on the house and wanted to share the full play-by-play for making jambs and hanging two interior doors, including how we routed hinge mortises and drilled for the knob.
Before this project the laundry room had no door and the storage room was closed off with a plastic drop cloth. Replacing those with proper doors made the space quieter, neater, and far more functional.

We considered a pre-hung door for the laundry room to avoid routing hinge and latch pockets, but we had a slab door we wanted to reuse and preferred a specific style for the storage room. That meant we needed to build jambs and cut the hinge and latch recesses ourselves. Home Depot sells inexpensive jamb kits for standard doors, and we used a 3-piece jamb kit (two sides and one top) sized for doors up to 36″ wide — ours are 32″.

The jamb kit has rabbeted ends so the head piece sits across the stiles. We trimmed the non-rabbeted end slightly so the jamb fit the framed opening. To assemble and fit the jamb we laid the door on scrap supports and assembled the jamb around it, accounting for the rabbet and leaving about 1/8″ clearance around the door for smooth operation.

Next came the hinge mortises on the jamb. Because the hinges were already mounted on the reused door, we transferred their locations directly to the jamb, then traced a spare hinge to mark the exact shape. For clean, repeatable cuts we used a compact router (a Rigid 1-1/2 HP compact router) with a hinge-cutting bit. After practicing on scrap and creating a small clamped guide to steady the router, we cut the hinge pockets on the jamb to the correct depth.

With the hinge pockets routed, we nailed the three jamb pieces together with 2″ nails and dry-fit the assembly into the framed opening. The most detail-oriented part of the install is getting the jamb plumb and level on all sides. We used shims under and behind the hinge locations and adjusted them until the jamb was perfectly plumb and the reveal around the door looked even. Once satisfied, we nailed the jamb into the framing.

After a few attempts (we had to tweak shims to eliminate a tight top corner), the door hung and closed correctly. We installed the strike plate and nailed the stop molding around the jamb, which creates the final edge the door closes against. The first door took longer than expected, but learning from that made the second installation much faster.

The second door was heavier and had three hinges, but we followed the same workflow. We made a template from scrap wood for routing hinge mortises and used it to mark and rout matching pockets on both the door and the jamb. Clamping a guide or using a template helps keep the router steady and yields more consistent pockets than freehand work.

Once the hinges and jamb were prepared, we assembled and shimmed the jamb into place, attached the hinges, and tested the fit. With Sherry’s help the heavier door went up much faster. It swung smoothly, stayed open when intended, and closed securely — the result felt very rewarding after the effort.

For the doorknob installation we used a simple drill-template kit to ensure accurate placement of the crossbore and latch pocket. The kit clamps to the door and helps guide the large hole saw for the knob and the smaller bit for the latch. We still routed a small recess on the door edge for the latch faceplate freehand with the router, then installed the knob and latch assembly and secured the strike plate in the jamb.

A couple of finishing notes: the hardwood floor stopped short of the door openings, so we added a short threshold piece. It looks intentional and ties the floors together visually. We’ll spray-prime and paint all the molding and finish the casings later when we finish the rooms. We also ordered matching doorknobs with decorative backplates so the hardware will be consistent down the hallway.

The improvements made a big practical difference: the laundry room is noticeably quieter with a door, and the storage room no longer requires that awkward plastic drop cloth. The project reinforced how a few careful measurements, a bit of routing, and patient shimming turn rough framed openings into professional-looking doors. If you’re tackling similar work, take your time on hinge locations, practice your router cuts on scrap, and use shims until the jamb is perfectly plumb — those steps make the installation go from frustrating to satisfying.

This little addition has come a long way in a short time — the laundry room wasn’t even drywalled a month ago. Small wins like this keep renovation momentum going: measure carefully, use templates where possible, and don’t rush the shimming. Just keep swimming.









