How to Run New Cable Wiring Through Walls
How I Installed a Cable Jack for a TV in Our Master Bedroom
One change we were excited to try in this house compared with the last was putting a TV in the master bedroom. In our previous home we briefly had a TV up there, but we never bothered to hook it up to a DVD player or get a second cable box—I’m not even sure it was ever plugged in.

This time, as two people who find it hard to stop working on laptops at night, we hoped a bedroom TV would encourage us to snuggle in and relax instead of staying in “blog mode.” We ordered two set-top boxes and thought we were one step closer to that dream.

However, the bedroom TV still wasn’t active. During pre-move service installation, the technician asked where to put the upstairs cable jack. Not wanting to commit furniture placement before moving in, I was told I could do it myself later. Whether he was persuasive or just in a hurry, the jack didn’t get installed—and our bedroom TV remained unused except for the occasional Blu-ray movie on weekends.

I’d never run wiring through walls before, so I approached the job cautiously. The plan was straightforward: run a coaxial cable from an existing splitter in the attic, down through the wall, and out at a new jack in the bedroom. Armed with the cable company’s basic tips and a few helpful videos, I climbed into the attic and began locating the right spot to drill.

To find the correct wall, I followed a visible electrical wire in the attic to identify the stud bay that aligned with the bedroom wall (the wall ran parallel to the joists). I also located the phone line that connects to the bedroom jack. Seeing both wires through the attic floor helped me feel confident I was working over the right section of drywall.

Translating measurements between the finished bedroom (with drywall) and the attic (with exposed rafters) was trickier than expected. Rather than overthink it, I used fixed reference points—like the visible path of the phone wire—to estimate where to drill from above.

Downstairs, I made a small exploratory hole with a jab saw where I wanted the new jack to emerge, hoping it would line up with the hole I planned to drill in the attic. The goal was to have the coax run cleanly inside the wall without creating a bunch of patched drywall later.

To connect the two holes I purchased glow rods from a home improvement store. These fiberglass rods are flexible enough to snake around framing and stiff enough to push through insulation. They even glow, which is useful for guiding them in the dark cavity between walls.

I pushed a long glow rod down from the attic through the insulation until I felt it hit the new hole. At first my measurements were slightly off—the rod ended up just to the side of the downstairs opening, basically on the other side of a stud. Rather than making more holes in the drywall, I drilled a few more access holes from the attic until I found one that lined up perfectly. It was a small victory.

After finding alignment I taped the coaxial cable securely to the glow rod and pulled it through the wall. Once the cable was in place I removed the tape and installed a simple coax wall plate I picked up from the store. The cable screws into the back of the plate just like it would into a cable box, and the plate screws to the drywall for a clean finish—definitely more polished than a cable poking up through a random floorboard.

In the attic I connected the other end of the coax to the existing splitter. Previously this splitter fed a guest room jack that we removed when installing new hardwood floors, so the splitter already had the infrastructure I needed.

We ran into a hiccup with our provider’s equipment: the set-top boxes needed a swap and there was a region-wide glitch that required a couple of trips to the store and a lengthy support call. While that was frustrating, the hardware and wiring work had been done correctly, and eventually the multi-room DVR service started working. Now recordings made on the downstairs TV are available upstairs—an amazingly convenient feature.


We placed the jack near the other outlet on the wall rather than hiding it behind the dresser because we plan to swap the skinny dresser for a wider piece later. It made more sense to keep outlets and jacks together for now so they’ll be covered when the new furniture arrives.

All told, the project cost about $40 in materials and took an hour or two of hands-on work (not counting time spent on support calls). We saved the provider’s installation fee—often quoted around $150—and I gained confidence after my first in-wall wiring job. It was satisfying to solve the problem myself and to finally enjoy cable TV in the master bedroom.
Psst—We announced this week’s big Kohler giveaway winner; see the original post for details and the Rafflecopter box to find the winner.








