How to Rehang Cabinets and Remove Granite Countertops
Kitchen Update: Removing the Wall Oven Cabinet and Replacing Appliances
When we last updated the kitchen, we were in the middle of moving appliances around. Before our new appliances arrived, we had to remove a few existing fixtures—first on the list was the tall cabinet that housed the wall oven.

We decided to remove the wall oven because the front was scorched, the finish was dated bisque, and it baked unevenly. We didn’t want to replace it with another wall oven for a few reasons: wall ovens are typically more expensive than ranges, our cabinet is unusually narrow so current ovens might not fit, and the tall cabinet felt bulky in a room where we preferred only the fridge and pantry to be the tall vertical elements. So the entire cabinet was coming out, although we planned to reuse parts like doors and drawers.

After emptying the cabinet, we unscrewed it from the wall, removed trim, and carefully pulled it out of its recess in the floor—after turning off the power. The unit was hardwired, so instead of simply unplugging it I had to detach some wiring connections. I capped the exposed wire, tucked everything into the metal junction box (which had a lid), and left the electricity off in that area until the electrician could come by to finalize the wiring and identify an additional mysterious wire above the pantry.

With a few more screws removed and some careful maneuvering, the oven came free and was taken out of the room. We plan to donate it to Habitat for Humanity ReStore.

The cabinet itself turned out to be fairly light once emptied, so it joined our stash of reusable kitchen pieces in the sunroom. We’re holding onto the doors, drawers, and trim until the remodel is complete in case we need them. Anything we don’t use will be donated or sold afterward.

The next morning our new appliances arrived. The fridge was installed in its new spot (the old refrigerator was hauled away and donated), and the new range sat nearby, not yet hooked up because it will be placed to the left of the fridge in the revised floor plan. The dishwasher and microwave were still boxed in front of the fireplace, so the kitchen looked chaotic, but the new fridge is already in use and we’re very pleased with it.

With the wall oven gone and the new stove not yet connected, we temporarily lost our ability to bake. Our next goal was to get the new range installed in its permanent spot, but first we had to remove the existing cooktop and the granite that supported it.

The cooktop was a JennAir drop-in that we hoped to sell or donate. We emptied the cabinet below and shut power to the area, capping wires and waiting for the electrician. According to the installation manual, the cooktop should have lifted out easily, but it wouldn’t budge. We discovered it had been glued in place with a heavy black silicone sealant.

Research turned up warnings: gluing a drop-in cooktop makes removal risky because the glass can shatter when you try to free it. We carefully tried to cut and scrape the caulk to lift the unit, but after slowly prying for about 15 minutes the glass developed cracks and ultimately fractured. Unfortunately, that meant the cooktop was no longer in condition to sell or donate.

With the cooktop compromised, we focused on detaching the granite. The backsplash came out surprisingly easily, which gave enough access to cut along the back edge of the cooktop. Even so, the cooktop still wouldn’t separate, so we decided to remove the entire granite section with the cooktop attached.

After slicing through the silicone caulk holding the granite, Sherry used a crowbar and screwdriver to pry up the slab. Once detached, we called in reinforcements—my dad—because granite is very heavy. With gloves and an extra pair of hands we moved the slab into the carport, where it now awaits sale or donation.

Back inside, the cooktop and granite were gone and the cabinet that had been under them needed to be removed to make room for the new range. After pulling a little more trim and unscrewing a few fasteners, the cabinet slid out and we positioned the new stove into place.

We left the protective wrapping on the range as a clear reminder not to use it until the electrician finishes converting the raw wiring to a standard plug. A few notes about the setup:
- Our microwave sits unusually low above the stove, so we look forward to replacing it with a properly mounted range hood.
- The stove is 30 inches wide while the previous cabinet opening was 36 inches. We’ll add 3-inch filler pieces on either side and paint everything white to create a built-in look without moving ductwork or re-centering the hood vent.
- The stove is counter-depth. It appears a bit forward in photos because we haven’t pushed it fully into place yet—the electrician will need to pull it back to finish the wiring.

We didn’t discard the 36-inch base cabinet—rather, we’re repurposing it in the new workspace that will extend from the built-in fridge to the peninsula we plan to add. Reusing this cabinet reduces the number of new cabinets we need to buy: only two will be required to complete the peninsula.

Every item we finish seems to reveal several more tasks, so our to-do list keeps growing. The major next steps include securing materials for backsplash, cabinets, and countertops, painting the exposed paneling, and scheduling the wall removal. We’ve chosen a contractor to help with the wall work, so hopefully that will move forward within the next month.








