Objectales

Popular

DIY Kitchen Sink and Granite Countertop Removal

featured 42473

Replacing Our Granite Countertops: How We Saved Money and Reused Our Sink

As Carla from Top Chef would say: hootie hoo! Our new counters are ordered, and we want to share what we chose and why. We found a price of $38 per square foot at Home Depot with no hidden fees, which came to roughly $1,700 for our project. We compared that to Lowe’s and a few local fabricators: local shops quoted around $55 per square foot, a big difference. Lowe’s initially matched the $38 price but charged extra for the sink cutout and a few add-ons that Home Depot included.

We sealed the deal when Home Depot agreed to match a 10% Lowe’s project coupon we received in the mail and also match the 5% discount we’d get if we used our Lowe’s card. That stacking of discounts isn’t available everywhere, so it paid to shop around and ask for price matching — it saved us a meaningful amount.

Another way we saved was by reusing our existing Corian sink. We like the sink and wanted to avoid the extra cost of a replacement. We’ve heard that seamless Corian sinks can be trickier to maintain than stainless undermount sinks, but keeping ours saved a few hundred dollars. The fabricator needed the sink in hand to template the new countertops accurately, though, so we had to remove the surrounding granite to free it.

img 42473 1

The removal process started with disconnecting the garbage disposal and the plumbing under the sink. Although it looks straightforward in online how-to guides, the mounting ring on our disposal was jammed and took about 45 minutes to loosen. On the plus side, I now know my disposal better than I did before.

img 42473 2

Next we removed the faucet — a component we plan to reuse for now. This step went faster after we found the installation manual online and reversed the procedure. With the plumbing and fixtures detached, it was time to take off the granite.

img 42473 3

Because we’d already removed a section of granite previously to make room for the stove, we had a sense for what was involved: it’s mostly physical work. We started by prying off the backsplash with a crowbar to get into the joint between the counters and cabinets.

img 42473 5

No sweat. Then we cut along the adhesive line that bonded the countertop to the cabinets and began prying the slab up. It came up more easily than we expected.

img 42473 6

img 42473 7

The heavy lifting was the real challenge. We recruited family to help, but the large granite slab proved far heavier than anticipated, and lifting it high enough to slide the sink out risked damaging the sink or the cabinets. Our suppliers had suggested removing the counters with the sink in place so the fabricator could template without warping the sink, but the slab’s weight made that option impractical.

img 42473 8

Instead we focused on freeing the sink from the underside of the granite. We gently slid a spackle knife into the seam where the undermount sink was glued to the counter, broke the seal in one spot, and then tapped around the perimeter with a hammer to separate the adhesive. My dad ended up doing most of that work, and after about 45 minutes of careful prying the adhesive released.

img 42473 9

Once the glue was removed we were able to hinge the granite slab up like the lid of a trunk and lift the sink out intact. The sink was just dirty, not damaged, which meant we saved roughly $200 by reusing it — a small victory worth celebrating. The shot below gives a sense of how large the sink is.

img 42473 10

With the sink set aside, we continued removing the granite. When we lifted the slab slightly we were relieved to find a crack that made it possible to split the slab into two more manageable pieces. However, beneath that crack we discovered a metal reinforcement rod installed around the sink opening — an unexpected obstacle that made separating the two halves trickier.

img 42473 11

img 42473 12

After sliding one half of the granite off and bending the rod enough, we used a screwdriver to pry the rod free and completely separate the slabs. Once separated, each half was light enough for two people to carry out safely.

img 42473 13

Here’s the scene before the final half came out — we even used an old towel to protect the new stove surface while working. With all the granite removed and staged in the carport to sell, our kitchen was officially sinkless.

img 42473 14

img 42473 15

The fabricator estimated we’ll be sinkless for about three to four weeks, with the holiday schedule factored in. I reconnected the dishwasher drain so we can still run dishes and retain a little normalcy. We’re definitely in a better spot than during our full kitchen gut job in the past, when we were without appliances for months.

If you’re planning a countertop replacement, shop prices carefully, ask about coupon and project discount matching, and confirm whether the fabricator will need to take the sink for accurate templating. Expect heavy lifting when removing slabs and watch for hidden reinforcement under the granite. Reusing a well-maintained sink can be a straightforward way to save money if you can safely free it from the countertop.

Have you ever tried lifting a long granite slab with a couple of friends, found reinforcement rods around a sink, or reused an existing sink during a countertop project? Share your experience — we’d love to hear what worked for you.