DIY Ardex Concrete Countertops: Step-by-Step Guide
We went ahead and gave our kitchen’s laminate countertops a concrete makeover. After sharing a sneak peek of the first coat in a previous post, we’re following up with the final results, a clear breakdown of our process, and a short in-action video to help explain how we did it.

We’re really pleased with the transformation. Photographs don’t capture the full effect, but the room now feels more modern and far less “laminate.” The photos read a bit cool and stark, but once we add colorful window treatments, accessories for the shelves and counters, and replace the faux-brick flooring and old stove, the space should feel completely refreshed.

This project wasn’t without its challenges: it required a lot of time and generated a lot of dust. Still, the end result makes the effort worthwhile.

Here’s a reminder of what the counters looked like before: creamy-yellow laminate with the usual burn marks and scratches. We applied the concrete finish to the main U-shaped kitchen counters plus the nearby eat-in nook. We haven’t sealed the surface yet, so the color will likely deepen slightly once we apply the chosen sealer.

We used Ardex Feather Finish for this faux-concrete surface. After seeing other DIY attempts and comparing costs, it seemed like a promising choice, but the project proved to be more time-consuming than it appears in photos.

As first-timers working across roughly 45 square feet of counter area, the process stretched across five days. It wasn’t technically difficult, but it was labor- and time-intensive. Below is a concise walkthrough of what we did and the supplies that were most useful.

Supplies
- Ardex Feather Finish: the base material we used for the concrete look. We used about 2.5 bags for our counters.
- Mixing buckets: a small bucket for mixing batches with water worked well for our modest-sized mixes.
- Measuring containers: separate containers for powder and water helped keep the mix ratio consistent.
- Sandpaper: a range of grits (we mainly used 60, 120, and 220) and a sanding block for better control.
- Spreading tools: a large 10″ drywall knife for broad areas, a 4″ putty knife for edges and backsplash, and a small knife for tight spots like around the sink.
- Cleanup supplies: sponges, paper towels, and painter’s tape for protecting walls and catching splatters (we later adjusted how much tape to use).
- Protective gear: dust masks or respirators, safety glasses, and gloves—especially important during sanding to protect skin and lungs.
We started by thoroughly scuffing the laminate with coarse sandpaper to promote adhesion. After a few minutes of hand-sanding we switched to sanding blocks and gloves to make the work easier and protect our hands.

The Ardex instructions suggest a 2:1 powder-to-water ratio, but that felt too stiff for easy spreading. We found a slightly thinner, toothpaste-like consistency worked best—thick enough to hold on the blade but fluid enough to spread smoothly. Ardex begins to set in around 15–20 minutes, so keep batches small.

Applying it to the flat surfaces was oddly satisfying—like icing a large cake. The big blade sped up coverage for broad areas, while the smaller spreaders helped with the backsplash, edges, and tight corners.


We recorded a short video during the third coat to show the spreading technique and how the product behaves. Watching the application in motion helped clarify the rhythm of spreading, waiting, and smoothing.
For vertical surfaces and the sides of counters we switched to a smaller putty knife. Applying most of the material to the top first, then finishing the sides, helped keep vertical areas from sagging.

Edges were tricky early on because material can build up. We discovered that after about 20 minutes the mix firms to a clay-like texture that’s easy to smooth with a damp finger—an effective trick for tidying edges and creating cleaner lines.

We initially taped the wall to protect it, but taped areas sometimes stuck to the concrete in spots. After the second round we removed most of the tape and found that pulling tape downward (rather than tearing sideways) produced a cleaner edge.

After each layer dried, the real work began: sanding. Sanding evens out ridges and prepares the surface for the next coat. We scraped obvious ridges with a putty knife, then sanded by hand. For all but the final coat we used 60-grit to remove major high spots quickly; for the final smoothing we switched to 220-grit to avoid deep scratches.


One satisfying trick was shearing off excess along the bottom edge with the small putty knife to create a crisp line. It was time-consuming, but that clean edge made a big visual difference.

The biggest surprise was the dust. Sanding produced a fine gray powder that settled everywhere, so we vacuumed and mopped after each sanding session to keep the area contained. Expect to spend extra time cleaning up between layers if you work inside a main living area.

After the first coat some laminate showed through along vulnerable edges, but multiple coats fixed those thin spots. The finish dries lighter than it looks when wet; sealing will likely deepen the color and remove the chalky look.


Below is the final look before sealing. The surface retains some imperfections—part of the industrial charm of a hand-applied concrete finish. It reads much more like stone than plastic now and gives the kitchen a heavier, more substantial feel.

At first I was hesitant about the imperfect character of the finish, but Sherry embraced it right away. I’m coming around—especially knowing that the sealer will deepen and slightly polish the surface, which should bring the finish together more cohesively.

The backsplash and areas around corners were the hardest to smooth because of tight angles and limited reach. We contorted into awkward positions to apply and sand these spots, which added to the physical challenge.

The sink area was another tricky zone. In a long-term installation we would have removed the sink for a cleaner result, but our plumbing situation made that impractical. Taping and carefully sanding around the sink produced acceptable results for now.

Overall, the space feels refreshed and much less yellowed. The update removed another dated surface and made a significant visual difference for relatively little cost.

The project took about 15 hours spread over five days, including prep and cleanup. Material costs were minimal: roughly three bags of Ardex (we used 2.5) at about $57 total, plus another $20 for buckets and sandpaper. That works out to roughly $1.71 per square foot for our 45 square feet of countertop—an economical alternative to full countertop replacement.

Next up is sealing. Choosing the right sealer is important: the wrong product can cause scratches, staining, or bubbling over time. Two commonly recommended options are Ardex Clear Concrete Guard High Performance Sealer and GST International Satin Seal Water-Based Acrylic Sealer. We’ll order one and document the sealing process and long-term wear so you can see how it changes the look and holds up.
Update: we later documented the sealer we used and tracked how the counters wore over time in follow-up posts.
Psst – Want to know where something in our house came from or what paint colors we used? We have a resource that lists items and colors for the house.









